How much bleach do I use to shock my pool?

If you need to calculate how much bleach or Clorox you need to shock your pool, you will have to use 1/2 gallon of bleach per 10,000 gallons of water to raise the chlorine levels by 5 ppm.

Can I use regular bleach to shock my pool?

Using Bleach as a Shock

You need to use less of such products per volume than you do if you simply add chlorine, and if you opt for chlorine alone, you need more bleach than you do pool chlorine. Bleach contains the same chemical -- sodium hypochlorite -- as pool chlorine, but the concentrations are different.

How much bleach equals a bag of shock?

One pound of 65% Cal-Hypo is equivalent to 117 fluid ounces (0.91 gallons) of 8.25% bleach. One pound of non-chlorine shock (43% MPS) is "equivalent" to 36 fluid ounces (0.28 gallons) of 8.25% bleach, but non-chlorine shock is not the same as chlorine.

Can you shock your pool with Clorox bleach?

Now you can know the gallons of bleach you would need to shock your pool as follows: use 0.5 gallons of Clorox per 10K gallons of water to increase the level of chlorine by 5 ppm. If you want to raise the level of chlorine by 2.5 ppm, then you would need ¼ gallon of the product per 10K gallons of water.

How much household bleach should I put in my pool?

Clorox itself recommends using between 100 and 200 ounces of regular-strength bleach per 10,000 gallons of pool water -- one gallon is 128 ounces, and many bottles of bleach are available in one-gallon or half-gallon sizes. Pool professionals tend to recommend more conservative amounts of bleach.

Using Clorox Bleach in Your Swimming Pool

Can you use bleach instead of chlorine in your pool?

6 reasons why you should avoid disinfecting your pool with bleach instead of chlorine. Finally, if it is not properly dosed, bleach can become dangerous for bathers! Pool water that is too concentrated in bleach can become toxic, irritating the eyes, skin, and respiratory tract of swimmers.

Is pool shock the same as bleach?

Swimming pool shock contains 12.5% sodium hypochlorite (bleach) vs. 6-8.5% for Clorox (bleach). Some Clorox products go as high as 8.5%. At a 12.5% concentrate, liquid pool shock is approximately 2x's stronger than Clorox bleach.

Can you put bleach in a vinyl pool?

High concentrations of chlorine (above 1.5 ppm) will attack the liner and bleach it, thus damaging it. Any level below this range will weaken its ability to kill off bacteria.

How long after putting bleach in pool Can you swim?

Liquid chlorine — In general, it's a good idea to wait at least four hours after putting liquid chlorine in the pool. The size of your pool and the amount of chlorine added does play a factor in this, too. Once your levels reach 5 ppm or lower, you're ready to swim.

How much bleach do you put in a gallon of water?

Mix 1 cup (240 mL) of bleach in 1 gallon of water. Wash surfaces with the bleach mixture. If surfaces are rough, scrub them with a stiff brush. Rinse surfaces with clean water.

Will bleach clear a green pool?

Green algae, unlike its black counterpart, is a true algae; it isn't resistant to chlorine, so you can control it by shocking the pool. If you don't want to spend a lot of money on expensive pool chemicals, you can shock with household bleach.

How much shock do I need for a 10000 gallon pool?

One pound of shock treats up to 10,000 gallons of pool water. Also, keep the pool filter and pump running for at least 10 hours during and after you shock.

How much shock do I need for a 1000 gallon pool?

Answer: The best thing to do is to take the reading for free chlorine first; then you can use pool calculator to find the amount of chlorine to add. Your free chlorine should always read 3 ppm. A 1000 gallon pool may just need 0.13 ounces or a little higher.

Can you over shock a pool?

Can you put too much shock in a pool? SKIMMER NOTES: It's unlikely but it could happen. It would take a lot of shock to really make the water unsafe for swimming. The best way to make sure you're safe to swim is to test your pool water and make sure free chlorine levels are between 1-4ppm for healthy swimming.

What is stronger chlorine or bleach?

Answer: It is true that pool chlorine is stronger than bleach. For bleach and water to be the same strength as pool chlorine and water, you would have to adjust the ratio, increasing the bleach and reducing the water. But no matter which chlorine you use, make sure to test a small area before doing the job.

What happens if you put too much bleach in a pool?

Excess chlorine can alter the pH level of the water in the pool, making it more acidic. The acid levels can cause any of the following symptoms: Irritant dermatitis which is a red skin rash characterized by raised itchy red bumps. Eye irritation and over-dilated blood vessels in the eyes.

What happens if you go in a pool that was just shocked?

In terms of swimming in a pool that has been recently shocked, you may be exposing yourself to the risk of skin and eye irritation. If this happens then rinse thoroughly with clean water for several minutes (source).

How long should you run filter after shocking pool?

While shocking your pool will help kill any germs any algae, it won't actually get rid of them; for that, you need your filter. So be sure to run your pool filter for at least 24 hours.

How much bleach do I add to my pool calculator?

If you need to calculate how much bleach or Clorox you need to shock your pool, you will have to use 1/2 gallon of bleach per 10,000 gallons of water to raise the chlorine levels by 5 ppm.

Is Clorox bleach the same as pool chlorine?

In truth, bleach contains the same base chemical as pool chlorine. That chemical is, of course, chlorine, and the only major difference between the two products is the concentration strength. Pool chlorine typically contains some form of stabilizer, as well, though this is not a crucial factor.

How much bleach equals a chlorine tablet?

Choose the sanitizer that best suits your individual preferences. *1 gallon of chlorinating liquid delivers the same amount of chlorine as 2 chlorinating tablets.

Can I use bleach to shock my above ground pool?

Bleach is safe and the only chemical you should be using in your pool unless cleaning pool tile with baking soda. So yes, you can use bleach to keep your pool water chemistry balanced.

How much shock Do I put in a pool calculator?

How much shock do I need to shock my pool? A simple ratio and a standard rule of thumb to follow when you shock your pool is to dissolve one pound of either calcium hypochlorite or sodium dichlor for every 10,000 gallons of pool water.

How much pool shock do I use?

Generally speaking, the dosage amount of pool shock is 1 lb. per 10,000 gallons, but consult the shock package label.