Why is my Whirlpool fridge and freezer not getting cold?

Dirty condenser coils are the most common cause for a Whirlpool refrigerator not cooling. Condenser coils dissipate heat as the refrigerant passes through them. If the coils are clogged in dirt and debris, they can't release the heat properly.

What would cause a refrigerator and freezer to stop getting cold?

Evaporator coils are covered in frost

But if the fan stops working, the coils may frost over. Remove the back panel in your freezer to see if the coils are frosted. If so, empty out the freezer and fridge, unplug the unit, and let the coils thaw for a day or two.

Is there a reset button on a Whirlpool refrigerator?

Press the door switches and the refrigerator temperature button three times within 10 seconds. After releasing the switches, there should be a letter "S" display in the freezer section and an "E" in the refrigerator's display. Press the fridge temp button once to get to the service moved.

Can you reset a refrigerator by unplugging it?

Yes, unplugging the refrigerator will reset the appliance, provided you leave the refrigerator unplugged and undisturbed for 45 to 50 minutes. When the refrigerator is unplugged, do not open the doors.

How do I reset my Whirlpool freezer compressor?

How to Fix Whirlpool Refrigerator Not Getting Cold Cheap and Easy

How do I know if my refrigerator compressor is not working?

Most everyone is familiar with the sound of a refrigerator kicking on and off. This may sound like a faint humming and you may not even notice it anymore because you are so used to it. That is the compressor. If you do not hear it, then it may be that your compressor is not working correctly or is broken.

How do I turn the cooling back on my Whirlpool refrigerator?

Why has my fridge gone warm?

Refrigerator Is Too Full

If there are too many items in your fresh food compartment, that cold air may not circulate properly, resulting in a refrigerator that's warm. It's fairly common for a refrigerator to feel warm if it's overstuffed, and this problem is obviously easy to resolve.

Is there a reset button on a refrigerator compressor?

Most don't automatically reset. If the appliance has a reset button, it should just need to be held in for 30 seconds to correct the fridge. Some refrigerators, including Maytag and Amana, need to have the lock button and the reset or auto buttons held at the same time to reset the fridge.

What is the first thing to check when a refrigerator stops working?

If Your Fridge Has Stopped and the Light is Off

As obvious as this sounds, often a fridge shuts down completely because it's simply getting no power. The first thing to check is the breaker (in your home's electrical service panel) of the circuit serving the fridge.

Why is my brand new Whirlpool fridge not cooling?

A Whirlpool refrigerator not cooling may have a dirty or damaged gasket that leaks cold air, warming the refrigerator's interior. Inspect the door gasket for damage, using a cloth dipped in warm water to clean away any dirt and debris. If the gasket is ripped or broken it will need to be professionally replaced.

How do I know if my refrigerator needs freon?

To tell if your refrigerator needs more Freon, simply unplug the refrigerator, turn off the temperature control and place your ear on the side of the unit. A hissing or gurgling sound indicates that Freon is present. However if you hear nothing it's likely that your fridge may be low on Freon.

How do I reset my Whirlpool refrigerator control board?

How much does a control board cost for a refrigerator?

A compressor or control board may cost $80 for a budget refrigerator, but upwards of $800 for the high-end models.

How do you know if your circuit board is burnt out?

Where is the defrost switch on a Whirlpool refrigerator?

The defrost thermostat is located behind the back panel in the freezer section. Once your refrigerator has been unplugged, the next step is to give yourself clear access to that back panel.

How do you know if your control board is bad?

Use some tape to keep the switch pressed down. If your control board has 120 volts AC going into it, then it has power. If your control board has power, but it's diagnostic light is not on, then the control board is likely bad and needs to be replaced. NOTE: You'll need a multimeter to test for power in your furnace.