What goes on roof before shingles?

Underlayment— This is the first layer of waterproofing that goes down in between sheathing and shingles. Underlayment seals the roof from damaging elements like snow, ice and rain. Also referred to as a membrane, underlayment is mandatory for providing the roof with a waterproof barrier.

What do you put on a roof before shingles?

Before laying down shingles, you need to protect the roof with sheathing. Roll out a single layer of roofing felt or tar paper, which serves as a moisture barrier. Begin this layer at the bottom of the roof and add it in horizontal rows, with a slight overlap to prevent leaks.

What layer goes under shingles?

Roofing underlayment is what lies between the shingles and the roof sheathing, or roof deck, which is typically either plywood or OSB. It's installed directly on the roof deck and provides a secondary layer of protection from the elements, including rain, snow, and wind.

What layers go on a roof?

What goes on first drip edge or felt?

Installing roof drip edge flashing properly

The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.

How to Install Roof Shingles

What goes on top house roof?

Made of fibreglass and asphalt, shingles protect the roof from rain and lend a house character.

What is the plywood under shingles called?

Chances are, the shingles on your roof were attached on top of a plywood base. Sometimes referred to as roof sheathing or a roof deck, this plywood acts as a foundation for the layers of underlay and the shingles on your roof and connects the roof to the frame of the house.

Is underlayment necessary for roof?

All roofs have underlayment. At a minimum, a roof with asphalt shingles should be completely covered with one layer of underlayment. Roofers may consider adding layers of underlayment for superior protection, which is especially useful on low-pitch roofs.

What is the difference between tar paper and roofing felt?

It's a generic term and sometimes used synonymously with roofing felt because they are used the same way. Tar paper is less wind and sun resistant than other underlayment systems. And because they are organic, the humidity and the heat will deteriorate them is much less time than Synthetics which are in-organic.

What are roofing nails?

Roofing nails are used in roof installation to fasten shingles, to install roofing felt for waterproofing and to attach roof tiles and sheet metal. There are different kinds of roofing nails, made of different materials and in various sizes. All roofing nails have wide, flat heads and short shanks.

What is drip edge?

Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components. Drip edge overhangs the sides of the roof and has a small metal flange that is bent away from the fascia.

What is the best sheathing to use on a roof?

What Type of Sheathing Is Best for a Roof? Oriented Strand Board, OSB, is currently the best choice for roofs. It's durable, water-resistant, and very cost-efficient. It also has a very consistent thickness, so you don't have to worry about weak or uneven spots.

What is the most common roof sheathing?

Today the most common types of sheathing are plywood or strand board. Plywood is more expensive but slightly stronger. Dimensional lumber is not used because it would be much more expensive and provides a lesser surface for nails or screws due to gaps between all the boards.

What should I use for roof sheathing?

Oriented Strand Board (OSB) or plywood can be used, although plywood will provide higher nail head pull-through resistance. Use panels rated as “Exposure 1” or better. Install sheathing panels according to the recommendations of the Engineered Wood Association (APA). Use panels no smaller than 4 feet long.

What is fascia on a roof?

The fascia is the attractive board along the side of the overhang and the roof that helps your roof appear finished. Your gutter sits atop the facia board. The fascia is also known as a “transition trim” between the home and the roofline. The fascia supports the shingles and helps to keep moisture out.

What are the metal things on roofs called?

Snow guards or snow brackets are roof-mounted metal “spikes” installed by your roofing contractor and designed to hold large amounts of snow in place and prevent them from falling in one big chunk. For areas prone to heavy snowfall, snow brackets can be an extremely useful addition.

What are the three main components that make up a roof?

It incorporates joists, trusses, and rafters. Together, these three types of beams make up a framework that gives the roof its shape.

Does drip edge go over or under shingles?

Drip edge can be installed after shingles have been put on. Simply lift up the lower ends of the shingles to place the drip edge. But make sure to put the drip edge underneath the felt underlayment along the eaves so water cannot get below the drip edge.

Should ice and water Shield go over or under drip edge?

Ice and water protector needs to be installed directly onto the roof deck after you have placed the drip edge at the eave. (The drip edge will be installed over the ice and water protector and other underlayments at roof rake edges.)

Is tar paper necessary under shingles?

Answer: Roofing felt is a layer of tar paper installed beneath the shingles to provide a backup waterproof membrane in case of leakage. Felt, otherwise known as underpayment, is required when asphalt shingles are installed as a first layer of roofing or when they are applied over wood shingles or a built-up roof.

What is flashing in roofing?

What is flashing? Flashing, made from either metal or a rubber membrane, is a part of the system that keeps water from entering through holes created in your roof. All roofs have penetrations: openings or holes in the roof surface which allow for elements like chimneys, flues, skylights and vents.