Do you need furring strips for pegboard?

Most pegboards need wooden furring strips mounted on the back to provide a gap so the pegs or hooks will fit properly. Use the pegboard measurement to determine the number of 1- x 2-in. furring strips you'll need.

What are furring strips for pegboard?

But wait, what is a furring strip?!

They're often used for cinderblock or concrete walls when you want to cover it up or attach drywall. In this case, furring strips are used to create some dead space between the pegboard and the wall so the pegs or hooks can fit.

Can you hang pegboard directly on studs?

Pegboard goes up pretty easily and can be installed over drywall or even bare studs (such as in an unfinished garage). The trick to installing it is to create a 1/2-inch or larger gap between the wall and the back of the pegboard.

How do you hang pegboard with furring strips?

Place the pegboard against the wall and align it with the outer edges of the top and bottom furring strips. For extra strength, use the same 2-1/2-inch wood screws as before fitted with washers. Start by screwing into the center support, then place a screw in each corner.

Do you need a gap behind pegboard?

Pegboard needs about 1/2 in. of 'standoff' space behind it so the hooks can be inserted.

How to Install Pegboard | Ask This Old House

How many furring strips do I need for pegboard?

furring strips you'll need. Assume one furring strip for each horizontal edge and for every wall stud (which are usually 16 inches apart). For example, a four-foot wide pegboard will need one strip at each end and two in the middle for a total of four.

How much weight can furring strips hold?

Furring strips may support 50 lbs now, but this is NOT the right type of lumber for supporting live loads. And remember, kids grow... then their weight increases.

How much weight can pegboard hold?

Pegboard manufacturers state the standard 3/16″ pegboard can safely hold 100 lbs of weight. The pegboard I tested showed a single peg can hold over 150 lbs without tearing or pulling away from the wall.

How thick should furring strips be?

How Thick Are Furring Strips? Standard furring strips are marketed as 1-in thick, with the exception of the 2-in x 2-in strip. The actual thickness is usually just under a full inch. This makes them extremely versatile for a multitude of construction projects.

How do you build a pegboard wall?

How do you make a pegboard sturdy?

If you want a sturdy pegboard, you need to look for the thickest board you can find! In our store, that meant the 4'x4′ pieces that were not primed. Instead of buying 1 sheet of 4'x8′ pegboard, we bought 2 4'x4′ pieces because they were so much thicker. This also helps for transport if you don't have a truck!

Can you paint pegboard?

Once your pegboard is primed and sealed off properly, you're good to use your favorite water-based or non-water-based paint to finish off painting your pegboard. Here's how to paint a pegboard for the best results: Make sure the primer is completely dry before applying the first coat of paint.

How do you keep Pegboard hooks from falling out?

Are furring strips necessary?

Whether it's the ceiling or the walls, furring strips are essential to ensuring that you'll always get a flat and smooth surface when the project is complete. When applying furring strips to your walls, they will have to be directly screwed or nailed into the wood or concrete wall.

What is a furring strip used for?

In construction, furring (furring strips) are thin strips of wood or other material to level or raise surfaces of another material to prevent dampness, to make space for insulation, or to level and resurface ceilings or walls.

Can you use plywood for furring strips?

Re: 1/2" plywood for furring strips

Just be careful not to strip the screws when attaching to the 1/4" plywood or you wont get them to counter sink enough to cover. You could also use 1/2" Plywood and 1/2" drywall but cut the drywall to butt against the stair stringer since it will not fit behind.

How do you use a pegboard in a garage?