Why does my circular saw keep jamming?

One of the most common issues that can cause your circular saw to keep stopping is if the blade is damaged, cracked, or warped. If the blade is damaged in any way, no matter if it works or not, you need to get rid of it and get a new blade. Using a damaged or warped blade is not safe in any way, shape, or form.

Why does my circular saw keep getting stuck?

Too much blade will become exposed to wood, and the blade can get stuck. Proper use can also be a culprit causing your circular saw to stop mid-cut. Make sure you are moving the saw in a straight line or using a jig to keep the cut straight.

How do you keep a saw from getting stuck?

Can you use wd40 on circular saw?

There are several moving parts in a circular saw which must be properly lubricated after all the chips and dust have been removed. We perform all this lubrication using WD-40 Specialist Dry Anti-Friction PTFE Lubricant.

Should I lubricate a circular saw?

On most saws, you don't have to lubricate anything, that's done during manufacturing. There are a few moving parts and a number of tools can be used to change the blade out. But even with such simple tools, there are still small maintenance things you can do to extend the life of your saw.

Saw Binding? Cutting Slow? Is it the Motor? or Changing the Blade fixes the problem

Why do saws bind?

A circular saw binds because of failure to ensure proper blade depth; setting the blade too deep presents a danger because more blade surface is exposed while cutting than a properly set blade. When the saw is too deep, kickback and binding will be inevitable.

How can you tell if a circular saw is bad?

Look for worn-down, chipped, broken and missing teeth or chipped carbide tips that indicate it's time to replace a circular saw blade. Check the wear line of carbide edges using a bright light and magnifying glass to determine if it's beginning to dull.

How do I know if my circular saw blade is dull?

How long does a circular saw last?

A good circular saw can last you for 10 to 20 years depending on the amount of use and how you maintain it.

Can I cut wet wood with a circular saw?

If you're cutting wet wood set the depth so that the entire gap between the teeth is clear of the board you're cutting. This will stop your saw and cut line from getting clogged with wet saw dust.

Why is my circular saw burning the wood?

A dull blade will make it hard to cut quickly, and the slower the feed rate of the saw, the more friction against the wood and the greater the likelihood of scorch marks. Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty.

How do you stop a circular saw kickback?

Kickback happens when the saw blade binds or stalls suddenly in the wood and the saw gets driven back toward you. So the key to preventing this is to make sure your blade doesn't bind in the wood.

Can you use wd40 on saw blades?

WD-40 Multi-Use is a great rust protection product and it will effectively protect your saw from building rust easily. Once you've got your hands on this product, go ahead and apply a thin and even coat on top of your saw blade and spread it using a clean and dry cloth. You can wipe off any excess with the same cloth.

What can I use to lubricate a saw blade?

Synthetic beeswax is stickier, softer and spreads easier than natural beeswax in the jewelry manufacturing world. I would say that the majority of jewelers use this in their workshops as a lubricant for drill-bits, burrs, wire drawing and of course to lubricate saw blades.

What is the most important maintenance on a circular saw?

Using the right blade for the job is one of the most important parts of circular saw maintenance. If you use the wrong blade, it could get damaged during the cut. Furthermore, using the wrong type of circular saw blade forces the tool to work harder than it has to.

Which side of the line do you cut with a circular saw?

When appearance matters, make cuts with the good side facing down, as circular saws can splinter the wood on the top side. Making your cut line on masking tape can reduce splintering. Start over if you see that you've veered off from the cut line instead of trying to curve your way back on track.

Why does my circular saw not cut straight?

What Causes a Circular Saw to Not Cut Straight. A faulty circular saw is likely to have issues such as an unstable blade or a warped blade edge. The problem could also be the way you operate the saw. If you do not operate the circular saw properly, it will not cut straight.