Which junction is forward best when transistor is used as an amplifier?

Which junction is forward biased when transistor is used as an amplifier? Explanation: For Transistor to be used as an amplifier, the emitter-base junction is forward biased and the base-collector region is reverse biased.

Which junction is forward based when transistor is used as an amplifier?

A transistor acts as the amplifier in an active region. In the active region, the emitter-base junction of the transistor is forward biased and the collector-base junction is reverse biased.

Which of the pn junction is forward biased when transistor is used as amplifier?

Emitter-base junction must be reverse biased, Collector-base junction must be forward biased.

Which junction is forward biased in amplifier?

Here the emitter-base junction is forward biased, and the base-collector junction is reverse biased.

When a transistor is used as an amplifier?

When the transistor is biased to use as an amplifier, the input signals cause the emitter current to flow, which later contributes to the collector current. This current when flows through the load resistor, it results in a large voltage drop across. This shows that a transistor acts as an amplifier.

Bipolar Junction Transistors - Common Emitter Amplifier

Which transistor is best for amplifier?

When a junction transistor is used as an amplifier in CE mode?

When a transistor is used in the common emitter mode as an amplifier, the base-emitter junction acts as input junction and collector-emitter junction acts as output junction. The input junction is made forward biased by applying forward voltage and output junction is made reverse biased by applying reverse voltage.

When transistor works as an amplifier the BE junction biasing should be always?

In a transistor, the emitter base junction is always forward biased, whereas, the base collector junction is always reverse biased.

When PN junction is reverse biased?

When a p-n junction is reversed biased, the negative terminal of the battery attracts the free holes in the p-type towards itself whereas the positive terminal attracts the free electrons in n-type towards itself.

Which junction is forward bias when transistor is used as an amplifier Mcq?

Which junction is forward biased when transistor is used as an amplifier? Explanation: For Transistor to be used as an amplifier, the emitter-base junction is forward biased and the base-collector region is reverse biased.

When transistor is used as amplifier its junction is forward biased junction is reverse biased?

To use a transistor as an amplifier, its input must be forward biased and output must be reversed biased. So, emitter-base junction must be forward biased and collector-base junction must be reverse biased.

What can a pn junction diode be used as?

P-N junction diode can be used as a photodiode as the diode is sensitive to the light when the configuration of the diode is reverse-biased. It can be used as a solar cell. When the diode is forward-biased, it can be used in LED lighting applications.

When the collector junction in a transistor is biased in reverse direction and the emitter junction in the forward direction the transistor is said to be is the MCQ?

Cut-off Region

The region of the output characteristics where both the junctions (emitter and collector) are reverse biased, is known as the cutoff region of the transistor. In order to cut off the transistor, it is not enough to reduce l_B to zero.

Where should be the operating point in order to make transistor work as an amplifier?

1. Where should be the bias point set in order to make transistor work as an amplifier? Explanation: To operate transistor as an amplifier, it requires more current amplification factor and in cut off and saturation, the current amplification is less, therefore active region is better to fix the Q point. 2.

Which is the best transistor configuration for amplifier and why?

Common emitter transistor configuration

This provides a good overall performance and as such it is often the most widely used configuration. As can be seen from the diagram, in this transistor configuration, the emitter electrode is common to both input and output circuits.

Why CE configuration is preferred for amplification?

Expert-verified answer

Thus CE configuration is best for amplification because of its high power gain (due to its both high voltage and current gain) and hence most widely used.

Which type of biasing is used in CE amplifier?

Which type of biasing is used in CE amplifier? Explanation: The single stage common emitter amplifier uses biasing commonly called “Voltage Divider Biasing”.

Which configuration is best suitable for amplification?

If CB configuration is considered for amplification, it has low input impedance and high output impedance. The voltage gain is also low compared to CE configuration. Hence CB configured amplifiers are used at high frequency applications.

What is transistor power amplifier?

A transistor acts as an amplifier by raising the strength of a weak signal. The DC bias voltage applied to the emitter base junction, makes it remain in forward biased condition. This forward bias is maintained regardless of the polarity of the signal.

Can we use pn junction as amplifier?

Since a p-n junction diode is used as a rectifier to rectify alternating current. That's why in order to rectify an alternating current one uses a diode. So option 1 is correct. In an amplifier, indicator, and modulator, a transistor is used.

When pn junction diode is forward biased then?

Explanation:When PN junction is forward biased then depletion region width and barrier height reduces.

What is forward bias in PN junction?

Forward bias or biasing is where the external voltage is delivered across the P-N junction diode. In a forward bias setup, the P-side of the diode is attached to the positive terminal and N-side is fixed to the negative side of the battery. Here, the applied voltage is opposite to the junction barrier potential.

When both junctions of BJT are forward biased it operates in?

With both junctions forward biased, a BJT is in saturation mode and facilitates high current conduction from the emitter to the collector (or the other direction in the case of NPN, with negatively charged carriers flowing from emitter to collector). This mode corresponds to a logical "on", or a closed switch.