Which is better for subfloor plywood or OSB?

OSB is considered more structurally consistent than plywood.

Since a sheet of plywood consists of several large veneers of wood, it's susceptible to instances of knots and other imperfections (which, if aligned, could create slightly softer spots throughout the material).

Is it better to use OSB or plywood for subfloor?

OSB has a lower resale value than plywood due to its lower strength. For this reason, few homeowners prefer OSB in their homes. Apart from costs, plywood is superior in all the other areas, such as the strength of the structure. For this reason, it's a superior material for use on the subfloor.

What is the best material to use for subflooring?

Plywood. Plywood is considered the most popular material used for subflooring, it has been used since the 1950s and remains one of the top choices for contractors. Standard plywood works perfectly fine as a subflooring material, but the best option is ¾” tongue-and-groove plywood subflooring.

Is OSB board good for subfloor?

Some builders prefer OSB over plywood for flooring because the surface, when new, is always clean, flat, and knot-free. Since OSB is so dense, it's a good soundproofing product. OSB is a more consistent product than plywood or other types of material for subfloor: every sheet is the same.

What lasts longer plywood or OSB?

OSB is usually more consistent across the board, meaning what you see is what you get. Plywood and OSB are generally considered to have the same load strength. However, as plywood has been around longer, it has shown that it can last 50 or more years in an installation.

Plywood Vs. OSB - Subfloor Comparison

Is OSB more water resistant than plywood?

OSB takes longer to get wet than plywood but also takes longer to dry out. When used as a roof sheathing, this tendency to hold moisture means it can degrade faster than plywood when exposed to chronic leaks.

What's cheaper OSB or plywood?

OSB is less expensive than plywood. To build a typical 2,400-square foot home, OSB may cost $700 less than plywood. OSB is considered by many to be a “green” building material because it can be made from smaller-diameter trees, such as poplars, that are often farmed.

What is the most durable subfloor?

Best for Durability and Maintenance: Plywood

As subfloor materials, both plywood and OSB should last as long as the house itself if the subfloor has been properly installed.

How thick should OSB subfloor be?

The minimum thickness of plywood for subflooring is about 5/8 inch. Since it does not hold fasteners as well as plywood, OSB must be a little thicker, or at least 23/32 inch.

What thickness of subfloor should I use?

Glue is sprayed between each layer and the sheet is hot pressed. CDX plywood should be a minimum of 7/16 inch thick. The thicknesses are as follows: 7/16-, 15/32- and 1/2-inch-thick panels require joists spaced 16 inches on center; 19/32- and 5/8-inch-thick panels require joists spaced 20 inches on center.

Do you nail or screw subfloor?

Ideally, nail down your subfloor using corrosion-resistant nails that will securely hold it in place and last a long time. Screws are a great alternative that you can easily remove, but they are not as sturdy. Screws are superior in terms of reducing floor squeaks, but the installation is slower.

Can I use plywood sheathing for subfloor?

As you can see, both OSB and plywood sheathing are good options for the construction of structural sub-floors. Both are strong, durable and long-lasting.

What can I use for subfloor Besides plywood?

Common Subfloor Materials. There are four primary materials used as subfloor: plywood, oriented strand board (OSB), concrete, and high-performance panels.

Can OSB subfloor get wet?

Your framing lumber and the oriented strand board (OSB) are going to be fine. The glues used to make OSB are water-resistant because the manufacturers know that virtually no one can build a home that won't get wet before the roof and siding is applied.

How do I protect my subfloor from moisture?

What is best subfloor for bathroom?

Plywood as a Subfloor Material

Traditionally, exterior grade plywood has been the subfloor material of choice for many bathroom flooring projects. Plywood is made by gluing alternating layers of wood veneer. CDX plywood (¾”) in particular is used often because it has a high level of resistance to moisture and humidity.

Do you need two layers of subfloor?

The subfloor has to be attached to the joists, and two subfloor layers glued together or just nailed through to the joists, is no different than one thicker subfloor layer.

Which side of OSB subfloor goes up?

Answer. OSB roof panels should always be installed with the grade stamp facing into the attic and the screened surface (with the nail guide lines) facing up.

Does subfloor need to be tongue-and-groove?

For subflooring, you use tongue and groove plywood. The tongue and groove are only along the 8 foot edges. On the four foot edges, your seams will fall on joist tops, so no need for tongue and groove. But to start off, we will need to remove the tongue so the plywood is tight with the exterior ICF walls.

What type of wood should I use for subfloor?

Plywood has been a standard subfloor material since the 1950s and remains the preferred subflooring for many builders. Standard plywood can be used for subfloors, but a better material is 3/4-inch tongue-and-groove plywood subflooring.

How many layers of plywood do you need for a subfloor?

If you are using plywood for your subfloor, you should use a minimum of one layer that is between ¾” and ⅝” thick. This thickness will suffice for most floors; however, codes will vary and a second layer is a good idea if your floor covering is going to be a heavy material like ceramic tiles or natural stone.

How long does it take OSB to rot?

Sheets situated so they air dry on both faces between wettings will outlast those that only dry on one side or are always damp. OSB, which is unable to dry out, can rot within a matter of months, while panels that can dry out may last more than a decade.

What is OSB board good for?

OSB is now used for about 70 percent of all floor, wall and roof sheathing in North America. Building codes, the Engineered Wood Association, architects and most builders rate plywood and oriented strand board (OBS sheathing) equal in strength and durability.

Is OSB load bearing?

Due to its inherent strength (see below), OSB is particularly suitable for load-bearing applications in construction but it also has a wide range of other applications.