Where does the yellow dot go when mounting a tire?

When performing weight match-mounting, the yellow mark on the tire, indicating the point of lightest weight, should be aligned with the valve stem on the wheel assembly, which represents the heaviest weight point of the wheel assembly.

When mounting a new tire Where should the yellow dot be placed?

Most manufacturers will place a yellow dot on the section of the tire where there is least weight. The technician is then supposed to line up this yellow dot to where the valve stem is located. Where the valve stem is located is the heaviest point of the wheel.

What is the yellow dot on a tire for?

Dot Marks The Spot

The yellow dots can help minimize the amount of weight needed to balance a tire and wheel assembly by mounting the tire so that its lightest point is already matched up with the wheel's heaviest point. The yellow dot indicates where the manufacturer has identified the lightest spot on the tire.

Do you line up red or yellow dot on tire?

If it is lined up with the yellow dot, the valve stem is located at the heaviest part of the tire. If it is lined up with the red dot, then it is located at the lightest part of the tire. These dots guide the technician to make sure that the tire is properly balanced during installation.

Where does the red dot go on a tire?

The red dot may be aligned with a 'dimple' on the exterior of the rim. This indicates a wheel's low point and should be adhered to in the mounting process. By pairing a dot with either the lightest or heaviest weight area, you will achieve the optimum balance point during installation.

Red

What color dot goes by the valve stem?

The Yellow Dot

When tyres are made, they are almost never perfectly balanced, and most manufacturers will place a yellow dot on the section of the tyre where there is least weight. When fitting a tyre, you should line up this yellow dot with the valve stem as this is the heaviest point of the wheel.

Why do new tires have colored lines?

It was developed to help manufacturers and distributors to avoid costly mistakes. Basically, such coloured stripes are the alphanumeric codes that precisely indicate various characteristics of a given tyre model, such as tyre size, type and other parameters.

What does a blue dot mean on a tire?

The blue dot represents the high runout location on the wheel, while a red dot on the tire represents the coordination runout position on the tire.

What does the white dot on a tire mean?

The White Dot (Dynamic Balancing Dot) Regardless of the type of wheel, if there is no red dot, mount the tire with the white dot next to the valve stem. The white dot indicates the overall light dynamic balance point of the tire. In other words, it's as though the white dot represents a bit lighter in the area of tire.

What are the yellow and orange dots on new tires?

Simply put – the tire is a bit lighter in the area where the yellow dot is located, and a bit thicker where the red dot is located. On an alloy wheel, the valve stem marks the heavy point of the wheel.

Which side of a tire faces out?

Whether it's directional or not, an asymmetric tire is designed to use one specific side as its outboard side. That side must always face outward regardless of any other positioning restrictions.

Where is the low point Dimple on steel wheels?

If the "dimple" method is used, the rim will exhibit a round dimple approximately 1/4" diameter in size which is pressed into the exposed rim surface under the bead flange area on the valve hole side. Unmarked rims of all types generally have the low spot at the valve hole.

How do you get paint off of new tires?

After rinsing your tires with a lot of running water, spray vegetable oil evenly and let it sit on the tires for at least two to four hours. This will allow the oil to break and degenerate the paint. After that period, drench the tires in the water again to promote oil greasiness, then scrub with a brush.

What are the lines on tires called?

TIRE GROOVES. The spaces between two adjacent tread ribs are also called tread grooves. These allow water to escape effectively.

Is when the yellow dot is matched up with the rim's heaviest point?

The yellow dot should be matched up with the rim's heaviest point, which is called weight matching. These points occur innately as part of the manufacturing process because it is impossible to create an absolutely perfect, even, round tire.

Can tires be mounted incorrectly?

If mounted incorrectly, a directional tire cannot be expected to work properly in wet or wintry conditions. If mounted improperly, directional tires may also wear irregularly and prematurely, and produce excessive road noise.

Can tires be installed backwards?

Installing and Rotating

On directional tires, there's an arrow on the sidewall of the tires — when correctly mounted, the arrow points toward the front of the vehicle. If directional tires get mounted backward, you won't get the hydroplaning resistance and other performance driving benefits the tread is designed for.

Do tires have an inside and outside?

If you have directional tires on your vehicle, they are simply marked by an arrow, and most of the time the word rotation, or direction of rotation, etc. Asymmetrical tires have an inside and outside to their tread. Tire manufactures will often do this to optimize the traction and wear capabilities of the tire.

What happens if the inside of the tire is outside?

If it is a non-directional tread pattern it will increase the tread life of the tire since the outer edges usually wear more, especially on the steering tyres (front). However, it requires dismounting from the wheel and flipping it over then remounting and balancing to put the inside to the outside.

What does T & H mean on tires?

Speed rating. This letter denotes the maximum sustainable speed and is found directly after the load index. For S-speed-rated tires, it's 112 mph; for T, 118 mph. Speed ratings for other tires include Q, 99 mph; H, 130 mph; and V , 149 mph.

Do tires have left and right?

It doesn't matter which side of the tire it's on. If they are directional this should be indicated by an arrow on the sidewall, which shows the normal direction of rotation.

Does it matter where you put your tires?

When tires are replaced in pairs in situations like these, the new tires should always be installed on the rear axle and the partially worn tires moved to the front. New tires on the rear axle help the driver more easily maintain control on wet roads since deeper treaded tires are better at resisting hydroplaning.