Where do fan cables go on motherboard?

How Do I Connect Fans to My Motherboard? As typical motherboard fan connector is a three or four-pin connector attached to the end of a PC fan's wire. This is attached to the three or four-pin fan header on the motherboard. There's no trick aside from lining up the notch on the connector with the guide on the header.

Where do case fan cables go?

Case fans can be installed directly into your Motherboard's 3 pin header or 4 pin header and if your case fan has PWM Connectors then you need to install it into your 4 pin Headers. You can plug your case fans into the PSU via a Molex connector.

Where do 3 pin fan connectors go?

As typical motherboard fan connector is a three or four-pin connector attached to the end of a PC fan's wire. This is attached to the three or four-pin fan header on the motherboard. There's no trick aside from lining up the notch on the connector with the guide on the header.

Can I plug in 3 pin fan into 4 pin?

Please Note: You can connect a 3 Pin Fan to a 3 Pin or 4 Pin header on the motherboard. The fan will function normally no matter type of fan header is used.

Do case fans connect to motherboard or power supply?

Power fan is for your PSU. On some units the fan will be speed variable, this is where you plug it into your motherboard to control the speed. Go ahead and plug your fans into your motherboard, advice like that is what you see in youtube comments.

Where do all your PC Parts Plug In?!?! Motherboard Connectors

Can I plug fans into RGB header?

Can You Connect Fan to RGB Header? If you have an ARGB fan, you can connect the fan to the RGB header. However, the RGB header needs to be a 3-pin 5V header and not the 4-pin 12V header. If you are trying to insert a normal case fan to the RGB header, it is not recommended.

Where do RGB fans plug into motherboard?

Install the fans in your PC case, and screw it in the designated areas. 3. Use RGB Y-Cable to connect the fan and the motherboard. Please use RGB 4-Pin connector to an RGB header, and 4-pin fan connector to a fan header on the motherboard.

Can I use RGB fans without RGB header?

Yes, they will definitely work even without an RGB header but only as simple fans. The RGB part of them won't be enabled. In that case, you'll have to purchase a ARGB controller and a HUB to connect and synchronize them.

Where do you connect fan hubs?

It requires one SATA power connection from the PSU and one 3 or 4 pin connection from the motherboard header to the Fan hub. The female end of the Fan Hub connects to the motherboard which then branches into several male headers for you to connect Fans to.

Can you plug fan into LED CPU?

You can plug practically any fan in any place on MB, they will just be controlled different ways. CPU_OPT fan will be controlled by CPU temperature and AiO pump may not be controlled at all.

What is a VDG cable?

The VDG is for some of the Gigabyte and Aorus motherboards that only used the 3 pin connection. other brands all used the 4 pin connector and Gigabyte swapped to that style on the more recent boards. You need to use the same connector that it shows for other brands that uses the 4 pin connector with 1 pin missing.

Where do you connect computer fans?

There are two common ways fans connect directly to a power supply. Either using a standard 4 pin power connector from the power supply, or by using an adapter board that converts the standard power supply connector to a motherboard style pin header connector.

Where do case fans plug into PSU?

Yes. Those fans are either/or. You can use either the 3-pin motherboard connector or the 4-pin molex direct from the power supply.

Are RGB fans 3 pin or 4 pin?

The 4-pin type is just called RGB. Its wires supply power at 12 VDC and three Ground lines - one for each of the three LED colours. Along the strip, all the LED's of one colour are connected to the same Ground line, so they ALL must do exactly the same thing.

Will a 3 pin RGB connector work with 4 pin?

You can plug a 3pin into a 4pin header for Fans but not ARGB You can't. 3-pin ARGB headers are 5V with a 5V pin, a single data pin, a blank spot and a ground pin. 4-pin RGB headers are 12V with 12V, red, blue and green pins. Plugging an ARGB strip into a non-ARGB header will blow out the strip.

Where does the PWM cable go?

Where do PWM cables go? The PWM cable goes directly into the Motherboard. Most of the users cannot install PWM cables just because they are putting them in the wrong Header. PWM cable comes with a 4-pin header, where most of the case fans are basically installed on three-pin headers.

What is a fan header on a motherboard?

The CPU fan header is for the CPU heatsink fan (or fans) only. The system senses the presence of this during startup, and controls the RPMs to regulate air flow as necessary. Connect the rear exhaust fan directly to the PSU using the Molex connectors (and adapters). Let it run at full speed for max hot air exhaust.

How do I connect multiple case fans to my motherboard?

To install more fans simply connect the adapters to each other, regarding one of them should be linked to the PSU by the male end, and other should have a female end not hooked up to anything. Some fans have a Molex power input instead of a 3-pin one, so you don't need any adapter to plug them to the PSU.

Do you need a fan hub for RGB fans?

No. You just need to connect the lighting node to a USB header on your motherboard. You will then connect the RGB cord from the fan(s) to the lighting node.

Do all motherboards have RGB headers?

Most motherboards come with two RGB headers, each supplying 12V of power. However, if you have a particularly large PC case that you plan on filling with multiple RGB fans, each requiring its own header, this quickly becomes a problem.