When Shocking a pool should the pump be on filter or recirculate?

The Filter setting is the best setting or filter position to use after shocking your pool. You may also use the Recirculate setting on your filter.

Should I run my filter when I shock my pool?

Run the filtration system

While shocking your pool will help kill any germs any algae, it won't actually get rid of them; for that, you need your filter. So be sure to run your pool filter for at least 24 hours.

Do you run pump while shocking pool?

Ensure the pool pump is running. Pour the mixture from the bucket into the water around the edges of the pool. Let the pump run for about 6 hours or more and test the water. Don't use the pool right away – wait for the free chlorine levels to drop to 1 – 3 ppm before it is safe to swim.

Should I run my pool pump on filter or recirculate when adding chemicals?

Reviewing Recirculation

This setting is used infrequently, but is helpful when you want to mix newly added pool chemicals or when you need to keep the pool water moving while you perform filter repairs.

When would you use recirculate on pool filter?

Recirculate - This setting is used to troubleshoot problems with the filter sand and is especially useful if you are battling an algae bloom. The water will circulate in the pool normally, but will bypass the filter sand.

3 Keys To POOL CIRCULATION And RETURN JET Flow | Swim University

Should you backwash after shocking?

Steps for Preventing Algae

If your pool is used frequently, shock it at least once a week. Clean or backwash your filter regularly. Run your pool pump for at least 10 hours per day to completely circulate the water. Keep your phosphate levels below 100 ppb (parts per billion).

How long does pool shock take to work?

Always run the pump when shocking the pool and allow it to circulate for 24 hours. The water should then be a blue or cloudy blue color. Test the water 24 hours after shocking and start adjusting pH and alkalinity levels. The chlorine will still be elevated, but over a few days, it should stabilize.

Why did my pool get cloudy after I shocked it?

High doses of chlorine, like pool shock, can cause temporary cloudiness as it kills contaminants. High levels of pH, alkalinity, and calcium hardness are more likely to cause cloudy water.

What does recirculate on a pool pump mean?

The Recirculate setting allows water to move through the filter without going through the filter media. Note: You can also use the Waste setting for this if you'd rather completely remove the dirty water rather than recirculate it back into the pool.

Can you put chlorine in pool without filter running?

Using a leaf net or a pole, manually apply chlorine and mix the water. Anything that gets the water moving could be effective. The only issue is that clearing the water without a filter is impossible. As a result of the fragments of dead algae remaining in the pool, algae may begin to grow anew.

Can I shock my pool through the skimmer?

Never pour pool shock into the skimmer, pre-dissolve for use in vinyl liner pools. When broadcasting shock across the surface, be mindful of the wind direction. Brush the pool after shocking, and filter the water for at least 8 hours afterward.

Can I swim 12 hours after shocking pool?

Can I swim 12 hours after shocking the pool? It's usually safe to swim after letting the shock circulate in the water for at least 8 hours. However, we recommend testing the water's chlorine level before swimming. A high chlorine reading may be uncomfortable and dangerous to swimmers.

Is it OK to run pool pump 24 hours a day?

A Rule of Thumb

Generally running your pool pump for 12-hours a day is a good option. This is based on the assumption that your average pool pump has a turnover rate of about 8 to 12-hours. That means that the total volume of your pool water will filter through your system 2 to 3 times per 24-hour period.

How long should you run pump after shocking?

With non-chlorine shock, 15 minutes is sufficient with the pump running. With using a chlorine shock, it depends on how, and what, you were “shocking” for. A maintenance dose per say, one would only need to wait approximately 4 hours with the pump running.

Can you put too much shock in a pool?

Can you put too much shock in a pool? SKIMMER NOTES: It's unlikely but it could happen. It would take a lot of shock to really make the water unsafe for swimming. The best way to make sure you're safe to swim is to test your pool water and make sure free chlorine levels are between 1-4ppm for healthy swimming.

Can I put clarifier in with shock?

It's not a good idea to use pool shock at the same time as clarifier. Some clarifiers are polymer based and the shock can act to break up the polymer causing the clarifier to be ineffective. It's best to shock your pool before and wait a day or two before adding clarifier.

How many times can you shock a pool?

How Often Should I Shock My Pool? Shocking your pool regularly will help to keep the water clean and free of contaminants. You should aim to shock your pool about once a week, with the additional shock after heavy use. Some tell-tale signs that your pool needs to be shocked are cloudy, foamy, green, or odourous water.

What should pH be before shocking pool?

Before you add shock treatment, you need to test your pool water and balance its levels. The pH level should be between 7.2 and 7.6, with total alkalinity being between 80 and 120 ppm.

What happens if you go in a pool that was just shocked?

In terms of swimming in a pool that has been recently shocked, you may be exposing yourself to the risk of skin and eye irritation. If this happens then rinse thoroughly with clean water for several minutes (source).

Is pool shock the same as chlorine?

Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.

How long does it take shock to clear a cloudy pool?

Thirdly, tripple-shock the pool using stronger Chlorine like In The Swim calcium hypochlorite (3pounds for 10k gallons) to kill all the algae; depending on the number of algae in the pool, it may take 2-3 days for the pool to clear up. The filter should run 24 hours a day for faster results.

Is it better to put shock in skimmer or directly in pool?

Let's start with the blanket rule: Don't – not even ever – pour pool shock down into the skimmer. Whether you're using shock granules or shock pods, all types of pool shock should be applied directly to the pool – and when we say “directly to the pool,” we mean like, the big open area where you swim.