When installing insulation Where is the paper?

Regardless of whether fiberglass insulation is installed in a wall, attic, or crawlspace; the paper facing should always face toward the inside of the home. That's because the paper contains a layer of asphalt adhesive which prevents water vapor from passing through it.

What happens if insulation is installed backwards?

So if it is installed upside down, the paper moisture barrier can actually keep moisture in-between the paper and the sub-flooring. This can lead to mold issues, as well as structural deterioration. Also, the paper is flammable so not properly installing it can create a fire hazard.

What side of insulation faces out?

Picking the right face is essential with fiberglass insulation that has a vapor barrier (meaning with Kraft paper or foil attached on one side). It should always face the warm-in-winter side. Thus, in cold climates, it should face the interior; in hot humid climates, it should face the exterior.

Do I remove the paper on the insulation?

To address the question above and based on the customer's particular situation, all they need to do is remove the Kraft paper from the insulation they've purchased to repair the hole. Luckily, the Kraft paper facing is easy to remove.

Which way should paper face on insulation?

Regardless of whether fiberglass insulation is installed in a wall, attic, or crawlspace; the paper facing should always face toward the inside of the home. That's because the paper contains a layer of asphalt adhesive which prevents water vapor from passing through it.

Right Vs Wrong: Installing Insulation Batts In Exterior Walls - Part One

Is the paper on insulation a vapor barrier?

The most common is paper-faced insulation. This type of insulation has a Kraft paper face with two flanges. The insulation is installed into the wall cavity with the paper facing into the house. This is very important — the paper, which is the vapor barrier, always faces the warm side of the house.

What is the correct way to install faced insulation?

The first layer should have the facing against the drywall to act as a vapor barrier. (The general rule for insulation is that the facing always goes toward the conditioned space.) The second layer of insulation should be unfaced so that moisture doesn't collect between the layers.

Should I use faced or unfaced insulation?

Unfaced insulation is non-combustible.

However, it's common for a layer of faced insulation to be used in the exterior walls and attic ceilings to prevent water from entering the home, while unfaced insulation can be added to improve the heat retention ability and reduce the risk of fire.

What is the difference between faced and unfaced insulation?

The Difference Between Faced And Unfaced Insulation

Faced just means that kraft paper is attached to the insulation itself. The paper helps improve the sturdiness of the insulation so it doesn't fall down as much. Unfaced insulation is just as good as faced, but it doesn't have that paper attached to it.

Does insulation need to be stapled?

INSTALLING FACED INSULATION WITHOUT USING STAPLES

Make sure the insulation facing is flush with the face of the stud. The insulation must fit snugly at the sides and ends. Some CertainTeed products, such as SpeedyR, are prodcuced without stapling flanges specifically to be friction fit, and do not need to be stapled.

Do you put plastic over faced insulation?

In most climates, it needs a vapor barrier. Some builders rely on batts with attached kraft-paper facing to do that job, but Tom recommends unfaced batts, covered in plastic with all the seams taped shut.

Where does the vapor barrier go in an attic?

The vapor barrier is always installed facing the heated side of the wall or ceiling, because that's where the moisture is coming from.

Can you put plastic over insulation in attic?

Plastic isn't recommended in this situation because it would create a second vapor barrier that can trap moisture and result in condensation and mold. Craft paper would have the same problem, this is what is most likely on the other side of the insulation for the vapor barrier you want.

Is it OK to use unfaced insulation in attic?

When installing between the roof rafters of finished attic spaces, you can use either faced or unfaced batting. When using insulation that has paper or plastic batting, that moisture barrier should face outward toward the attic space.

Do you need a vapor barrier for insulation?

Because it is mostly hot and very humid outside the building, the vapor barrier should be installed on the exterior of the insulation. This is recommended to keep the outside moisture from getting into the less humid, cooler interiors and damaging the building's structure.

Should you tape batt insulation?

To be clear, taping batt insulation is only worthwhile if the tape will make a vapor or air barrier more continuous. Tape is rarely a suitable method of securing batts in place. Instead, if you are looking to fix batts to your framing assembly, use twine, staples, or a combination of both.

Should you put plastic between insulation and drywall?

Without poly beneath the drywall, water vapor hits the drywall and diffuses through to the drier (in summer) indoor air. By installing a sheet of poly there, you cut off that drying mechanism and water that finds its way into walls can stay there longer and do more damage.

Where should vapor barrier be placed?

Vapor barriers are usually best installed on the side of the wall that experiences the hotter temperature and moister conditions: the inner surface in colder climates and the outer surface in hot, humid climates. In existing spaces, oil-based paints or vapor-barrier latex paints offer an effective moisture barrier.

What kind of stapler should I use for insulation?

The staples that work the best are the TacWise 53/8mm 5/16″ Staples. WARNING: Remember to leave your power on, even though your stapler is cordless. We'll tell you more about why it's safer to leave the power connected below. Never use ordinary metal staple guns when stapling insulation under a floor.