When handling cords and cables you should never?

Never use staples or nails to attach cords or cord bundlers to a surface, such as a baseboard or a wall. They could puncture the insulation and create a shock or fire hazard.

When handling a power cord you should?

What does OSHA say about cables?

Cable assemblies and flexible cords and cables shall be supported in place at intervals that ensure that they will be protected from physical damage. Support shall be in the form of staples, cables ties, straps, or similar type fittings installed so as not to cause damage.

What are three safety guidelines for power cords?

Do match up the plug and extension cord on a polarized cord (one hole on the plug is larger than the other). Do keep extension cords away from water. Do use GFCI (ground fault circuit interrupter) protection when using extension cords in wet or damp environments. Do keep extension cords away from children and animals.

What not to do with extension cords?

Using extension cords

Never use indoor extension cords outdoors. Don't plug multiple cords together. Don't run extension cords under rugs or furniture. Never tape extension cords to floors or attach them to surfaces with staples or nails.

Kids Safety

What is the OSHA standard for extension cords?

All extension cords used on projects must be three-pronged and carry one of the designations required by the Occupational Safety and Health Administration (OSHA) and the National Electric Code (NEC). Each extension cord, power tool and receptacle, as defined earlier, shall be tested for grounding continuity.

What are good ways to ensure the safety of cords and wires?

Always tape extension cords to walls or floors when necessary. Do not use nails and staples because they can damage extension cords and cause fire and shocks. Use extension cords or equipment that is rated for the level of amperage or wattage that you are using. Always use the correct size fuse.

What are 3 acceptable ways to support cable runs?

The support system provides a protective pathway and is designed to eliminate stress that can damage the cable. Typical cable-support systems include cable trays, ladder racks, enclosed wire pathways, clamps, rings, and fasteners.

What are the 3 most common personal safety requirements when using power tools?

What are the five basic safety rules that should be followed when using power tools?

What are the safety cable standards?

The cable must be at least ¼” in diameter. Flagging must be present at a minimum of 6' intervals with high-visibility material. Must have a smooth surface so an employee does not sustain a puncture, laceration, or possibly snag their clothing. The system is properly spliced or terminated at walls, columns and posts.

What are the OSHA guidelines for use of flexible cords?

The OSHA construction standard requires flexible cords to be rated for hard or extra-hard usage. These ratings are derived from the National Electrical Code, and are required to be indelibly marked approximately every foot along the length of the cord.

What are the 4 OSHA standards?

There are four groups of OSHA standards: General Industry, Construction, Maritime, and Agriculture. (General Industry is the set that applies to the largest number of workers and worksites). These standards are designed to protect workers from a wide range of hazards.

How should you secure cords in your workplace?

Clip it to keep it handy.

Desktop clips help keep these small cords organized and easily accessible. For larger cords, use cable clips and hooks to lift cables out of the way and keep them secured in place.

Why should we not touch the power cords of the computer?

When we touch the electrical appliances with wet hands ,the electric current passes from the appliance till our hands due to which we may get electric shock.

What are 10 electrical safety tips?

What are the four 4 rules for the use of hand power tools?

What are the 4 types of personal safety?

Eye protection – for example, spectacles/goggles, shields, visors. Hearing protection – for example, ear muffs and plugs. Hand protection – for example, gloves and barrier creams. Foot protection – for example, shoes/boots.

What are 3 types of cable termination?

The industry uses types of cable terminations – it can be heat-shrink type, cold-shrink type or Pre-moulded push on type cable terminations. Heat shrink type cable terminations, as the name suggests, the components or tubing's are shrinkable type when exposed to heat.

What are some best practices for managing cables?

Why is safety in handling cables important?

When installing any type of wire or wiring system, there is always risk involved. These risks of course include harming yourself, someone else or loss of property if the wires are not properly installed or necessary precautions are not taken.

What should you ensure cables do not do?

What is the most common OSHA electrical violation?

The most frequently violated standard is the failure to prevent the release of hazardous energy while employees perform servicing and maintenance activities.

What are extension cords a safety hazard?

Extension cords can overheat and cause fires when used improperly. Overheating is usually caused by overloading or connecting appliances that consume more watts than the cord can handle. Damaged extension cords can also cause fires.