What sizes do drawer slides come in?

Length. Drawer slides typically range in length from 10 inches to 28 inches with specialty lengths available for custom drawers and unique applications. If the slide is too short the drawer will not pull out far enough and if the slide is too long the drawer will not fit in the cabinet.

What size drawer slides are available?

Slides come in lengths from 10" to 28". A too-short slide prevents the drawer from opening fully, and one that's too long won't fit in the cabinet.

Can drawer slides be longer than drawer?

You should always use the longest slide possible for your application, without exceeding the drawer depth into the cabinet. The Height of a Drawer Slide is usually only a limiting factor, in the sense that you can't install a slide that is taller than your drawer or pull-out.

How wide are standard drawer slides?

Most vanities have 16 or 18-inch drawer slides. Similar to a kitchen cabinet, and with the standard vanity top depth at 21-inches, you'll find the finished depth of vanities mostly support a 16 or 18-inch drawer slide.

What are the different types of drawer slides?

Drawer Slides EXPLAINED – How to choose the right drawer slide

What are standard drawer sizes?

You can expect to find 5 inch or 7-inch-high drawers in 18-inch, 24-inch and 30-inch widths with a 14-inch depth. People who own this type of drawer swear by them, claiming the soft sides allow the drawers to hold more than a similarly sized wood drawer box.

How do you measure drawer size?

Begin by measuring along the bottom floor of the drawer at the back edge, middle, and front edge. Check for variations across the height of the drawer as well. Take the smallest of these measurements. Repeat this step for the depth measurement on the left edge, middle, and right edge across the floor and the height.

How much smaller should a drawer be than the opening?

Drawers can be built almost any width for bottom mount, but the most common size is 3/4-inch smaller on both sides than the cabinet opening. For example, if the opening is 12 inches wide, the drawer should be built 10 1/2 inches wide.

Can a drawer slide be shorter than the drawer?

If your drawer box is 16" you would order a 16" drawer slide. If the drawer measurement is slightly off and is just a tad shorter than the full 16" (as an example) 15 -3/4", you would order the next size shorter to ensure the drawer will fully close.

What is the difference between bottom mount and side-mount drawer slides?

Side mounts are connected on the side of the drawer and cabinet. Bottom mounts are attached to the bottom of the drawer and side of the cabinet. Meanwhile, undermounts are two slides attached to the underneath (invisible) of the drawer and side of the cabinet.

Do drawer slides need to be the same length as drawer?

Typically, side-mount ball-bearing slides should be the same length as the drawer box. For undermount slides, be sure to check the spec sheet—drawer boxes for these slides must be built to specific depths (front to back) in order to work properly.

How do you measure drawer runners?

Drawer runners are measured by the longest dimension of the fully closed side, and so should snuggly fit the inside the length of the drawer. Normally, you will be able to remove your previous drawer runners (assuming they are not warped or bent) and get the measurement from these.

How do you measure drawer pulls?

Place the drawer pull on a work surface with the threaded posts facing up. Measure from the center of the screw hole in one threaded post over to the center of the other screw hole with a tape measure. This is the measurement required when selecting replacement pulls.

Do kitchen drawers come in standard sizes?

Kitchen drawers, or drawer boxes, correspond with the size of your cabinets and their intended uses: For base cabinets, drawers range 6-36" in width, 4-10" in height, and just under 24-36" deep, depending on the depth of the base cabinet (which could also be the island).

How wide are most kitchen drawers?

24 inches is a moderate size that looks good in most kitchens. 30 inches are for those looking to add pull-out drawers or perhaps use the space for more food storage.

What is the standard size of a chest of drawers?

Standard Sizes

Although there is no standard size for a chest of drawers, the most common size is 38 inches wide. A chest of drawers this size is small enough to fit in most bedrooms, but large enough to have ample storage space. The drawers are also small enough that they won't buckle or sag over time.

What is a Euro drawer slide?

European drawer slides are inexpensive and easy to install, with a good medium load rating . They mount directly to the bottom of the drawer side, and to the inside side of the cabinet. Their low cost and ease of installation can often make them a good choice.

What kind of slides do you use for dresser drawers?

What is the sliding part of a drawer called?

A drawer slide drawer member is the portion of the drawer slide that attaches directly to the drawer. Drawer slides come apart in two pieces (sometimes 3). Each piece is called a "member".

How tall should slides be?

Slides up to 4 feet in height should have an exit height of 11 inches or less. Slides over 4 feet in height should have an exit height of at least 7 inches but no more than 15 inches. The exit region of slides should be essentially horizontal and have a minimum length of 11 inches.

How tall is a slide?

What is the length of the slide? Generally for slides the length is about twice the deck height it is made to fit. For example, a slide that is meant for a 5 ft deck height will be approximately 10 ft long.