What size tip should I use to spray clear coat?

Clearcoats should be sprayed with a 1.3 to 1.7 nozzle. Sealers and single-stage urethanes should be sprayed with 1.4 to 1.6 nozzles.

Can you use a 1.4 tip for clear coat?

The 1.4mm tip set up is ideal for use with base coats, clear coats, single stage, primers and other light to medium and some heavier viscosity paint coating materials. The 1.4 mm is a very universal tip size.

What is a 1.7 tip used for?

1.6-1.7MM- This larger tip is great for base coats and allows you a larger deposit of the coating on the surface. Some more experienced painters will use a larger tip like this, but it takes some expertise in mixing and gun setup to avoid runs and thick coatings of clear.

What pressure do you spray clear coat?

When spraying base coat clear coat systems, you want to spray at 26-29 PSI. You measure this PSI by pulling the trigger and letting air flow through the tip of your gun with your dial or digital readout saying 26-29 PSI.

What is the best size nozzle for spray painting?

Heavier coatings will require a larger orifice size than lighter ones. For example, primers are usually thicker than the accompanying paint so you should use a 1.7 or 1.8 mm tip to prime most surfaces. Most painters will stay in the range of 1.2 to 2.0 mm unless the paint being applied is specialized.

Simple Tips For Painting A Car - HVLP Paint Gun Needle

What is a 519 spray tip used for?

Achieve greater control and less overspray on different surfaces with a wide range of coatings, from stains to exterior paints. 10 inch spray pattern ideal for larger surfaces such as houses/buildings, walls and ceilings. The .

Can you spray base coat with 1.3 tip?

A general rule of thumb is: Heavy-bodied primers and primer surfacers work best when you use a nozzle size of 1.7 to 2.2. Basecoats should be sprayed with a 1.4 to 1.6 nozzle. Clearcoats should be sprayed with a 1.3 to 1.7 nozzle.

What is a 313 spray tip used for?

6 inch spray pattern ideal for narrow surfaces such as fences, decks and furniture. The . 013 inch hole size optimal for spraying medium materials like solid stains, interior latex or polyurethanes. Less overspray shortens cleanup time with less wasted material.

What size HVLP clear coat tip?

For spraying clear coats on small parts and projects, we recommend a 1.2mm tip. For spraying a whole car, a 1.3mm tip is recommended. The 1.4mm tip is perfect for base coats and metallic as the droplet size allows the particles to self-orient to eliminate streaking and mottling.

What is a 517 spray tip used for?

OVERVIEW. The reversible RAC IV SwitchTips are the most widely used tip for spraying a variety of coatings from lacquers to exterior paints. Use the Reverse-A-Clean (RAC) feature to quickly clear tip clogs by simply twisting the tip and spraying in the reverse position.

Can you spray primer with a 1.3 tip?

1.3mm is an excellent nib for general clear coatings, and is also suitable for thinner primers, water-based and single-stage paints. However, coatings that are too thick will not flow well through this size. 1.4mm-general size. Suitable for most primers, even thicker varnishes.

What psi do you spray primer?

You want to set it with the trigger pulled. To begin, set it at 50 psi. Close the air volume control knob (usually located beside where the air hose enters the gun) and with the trigger pulled, open it to the point where the air volume starts to stay the same, and then stop.

Why is my clear coat not glossy?

The likely cause is that the paint was applied too thin per coat or the nozzle was too far away. A coat thick enough to get a glossy sheen is seen but not too thick that runs develop is the proper technique. Practice on a similar surface is suggested.

What size is a 515 spray tip?

Thus, a 515 tip denotes an orifice measuring 15 thousandths of an inch in diameter.

How do you know if paint is thin enough to spray?

What is a 210 spray tip used for?

Fine finish spray tips are used for cabinetry, furniture and interior trim work (for a smooth fine finish) example Graco FF LP spray tips: 210 or 310. Low pressure tips are used primarily for spraying with pressures between 55 to 76 bar (800 to 1100 psi).

How do I choose a spray tip?

To Choose The Right Tip For Your Spray Project, Follow These Recommendations: Choose a tip with an orifice size rated for the paint or coating you'll be spraying. Light coatings such as lacquers, stains, and enamels require a small tip, while heavier coatings such as texture require larger spray tips.

What is a 213 spray tip used for?

The 213 SwitchTip has a 0.013 inch orifice and produces a 4 to 6 inch fan. Reverse the SwitchTip to easily clear clogs. Used for residential, commerical or industrial applicaitions. Best used with materials ranging from lacquers, latex paints and mastics.