What size staples should I use for tar paper?

Tack or fasten roofing felt using stainless steel ¼” to ½” T50 staples or 7/8” to 1-1/2” hot-dipped galvanized or aluminum 12-gauge shank roofing nails with a 3/8” head diameter. Use the nails with or without plastic caps.

Can you use staples for tar paper?

Tack the tar paper in place with a hammer tacker with roofing staples. Alternatively, you can use galvanized nails and a hammer or an electric staple gun with roofing staples. Space out the nails and staples along each edge, and scatter some along the interior of the tar paper strip.

What size are roofing staples?

Also, a roofing nail head is approximately 1/4 inch in diameter. A roofing staple is a little more than 1/16 inch wide.

Can you use staples for roof underlayment?

Some roofers prefer to attach felt underlayment with 1-inch roofing nails or special nails with plastic washers, but most codes allow staples, which are easier to drive.

Can you use staples for roofing paper?

With staples or plain roofing nails, the heads can sometimes tear right through the underlayment. However, depending on local roofing and fire codes, it may be appropriate to secure synthetic underlayments with staples. They're certainly faster and easier to install!

Best Staple Length For Targets

Can you use a staple gun for roofing felt?

Staples can be used for tacking it down, but not recommended to hold. When the shingles are installed the felt is not going anywhere. Back in the day all I used was staples and /or roofing nails now plastic tops are the norm.

What are T50 staples used for?

T50 staples are the world's best-selling heavy-duty staple platform. Made to deliver exceptional holding power, these staples are used for all heavy-duty stapling applications – from installing insulation, housewraps, and roofing underlayments to upholstering fine furniture and window treatments.

What are roofing staples?

The type of fastener used to fasten the shingles is especially important in resisting wind uplift and pull-through. Fasteners for asphalt shingles should be roofing nails or staples. The head of a roofing nail or the crown of a staple is what actually holds a shingle in place.

What size roof nails should use?

Roofing nails should be round-headed, sharp-pointed 11-gauge galvanized steel or the equivalent corrosion-resistant roofing nails. Nail head sizes recommended are 3/8-inch to 7/16-inch diameter. Nail heads should be low profile, smooth and flat. Nails should comply with ASTM F1667, Type I, Style 20.

Can I use framing nailer for roofing?

The nails that a framing nail gun shoots out simply cannot hold shingles but will shoot through it. The secret to keeping the roof shingles intact is a nail with a larger head flushed perfectly on the shingles and hence a dedicated roofing nailer.

What goes on first drip edge or felt?

Installing roof drip edge flashing properly

The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.

How much do you overlap tar paper?

Lay roofing tar paper when you have at least one other person to help. Place approximately 5 feet of tar paper at a time. Overlap each piece 2 inches over the piece before it. This ensures a secure barrier against moisture.

Which side of tar paper goes down?

When laying sheets of tar paper, always lay the sticky, glossy side down. Tar paper's two sides are noticeably different. One side is somewhat sticky, though don't expect it to leave a glue-like residue on your hands. The other side is smooth like paper, and typically contains lettering and line markings.

Can you staple roofing?

Today, staples are considered an inferior method of attaching shingles to a roof, but it's easy to understand why roofers like staples. Staple guns are smaller and better balanced. Coil nail guns are literally fed with a coil of nails, and the holder for the nails makes the gun much bulkier.

Should roof shingles be stapled or nailed?

Roofing nails are highly preferred to staples for asphalt and other types of roofs because they offer more holding power, meet building codes, and are easier to install correctly.

What is the difference between tar paper and roofing felt?

The slight difference between the two is that tar paper is made of tar, while roofing felt is simply a fiberglass mat made of a synthetic, inorganic material known as asphalt. Whichever you opt to use on your roof sheathing, rest assured that it will prevent water from leaking into your house and causing damage.

What size staple do I need?

The default rule is that the staple should be three times longer than the thickness of the material. When fastening hard wood, the staple should be twice as long as the thickness of the wood.

What is the difference between JT21 and T50 staples?

JT21 staples are the T50's little brother. Although often referred to as light-duty, there's really nothing “light” about them. Built with the same quality and precision as the T50, these staples utilize a thinner wire in a smaller staple format to deliver great holding power.

Are all T50 staples the same?

A T50 staple is defined by its flat top (the “crown”) which is 10mm wide (3/8″). The staples then come in a wide variety of lengths including: 6mm (1/4″) 8mm (5/16″)