What part of the room do you drywall first?

Hang drywall on the ceiling first, then the walls. Check the ceiling for bowed joists using a 4-ft. level. Irregularities less than 1/8 in.

What should you drywall first?

When hanging the drywall on the walls, always hang the top sheet first. Raise a sheet tight to the ceiling and secure it with a drywall nail at the top and bottom at each stud.

Does it matter if you drywall ceiling or walls first?

Yes, you should install drywall on the ceiling before the walls for multiple reasons: The drywall on the walls can support the ceiling pieces. You can create tight and fitted corners more easily. The pieces are easier and faster to work with from the top.

Why do you hang drywall on the ceiling first?

Doing the ceiling first means you can lift the wall sheets to make a tight joint. By contrast if you do the walls first you would have to sculpt every edge to make it seat tightly, and/or end up with lots of voids to fill before you tape.

How far should drywall be off the ceiling?

In fact, when you're hanging the ceiling, keep in mind that 1/2 in. along the perimeter will be covered by drywall on the walls. And the same is true of inside wall corners. So you can safely cut these pieces 1/4 in.

Drywall Basics | Drywall Installation Guide Part 1

Should drywall touch the floor?

Drywall should NOT touch the floor. Allow for floor and wall expansion without cracking the drywall by keeping a 1/2-inch (1.27-cm) space between them. This space also aids in preventing moisture from seeping if the floor floods.

Why do you hang drywall sideways?

Horizontal hanging reduces the lineal footage of seams by about 25%. Keeping the footage of seams to a minimum will result in less taping and a better looking finished job. Hanging horizontally also allows the drywall to flow over the framing so that bowed studs create less of a problem.

Is it better to run drywall vertical or horizontal?

As a general rule, for commercial buildings, drywall should be installed vertically. On the other hand, for residential buildings, it's best to install drywall horizontally to increase structural shear strength.

Should there be a gap between drywall and floor?

It might sound counter intuitive at first to leave space between your floor and your wall, but you should always leave a ½ inch to ⅝ inch gap between drywall and the floor.

Why do you stagger drywall?

Ultimately, staggered seams are stronger because the joints – the weakest part of the wall or ceiling installation – are minimized. Staggered joints are also less visible and easier to conceal for a flawless finish, offering a smoother, more professional look to the completed job.

Do you start drywall from the ceiling?

Hang drywall on the ceiling first, then the walls. Check the ceiling for bowed joists using a 4-ft. level. Irregularities less than 1/8 in.

How much gap should be between sheets of drywall?

Always leave a 1/2-inch gap at the floor. This allows for floor and wall expansion without cracking the drywall.

Does drywall have to end on stud?

Drywall Is Not on a Stud

All edges of all sheets of drywall must land on a solid surface such as a stud. A hanging drywall edge may work in the short-term, but in the long-term it can result in cracks and other serious wall issues. Sometimes, the drywall does not horizontally reach a stud.

How many screws go into a sheet of drywall?

So, how many screws are needed per sheet of drywall? The short answer: 28 screws are needed for attaching a 4-by-8 sheet of drywall. If it's 4-by-12, it'll take about 36 screws. When screwing drywall sheets (4-by-8) to the studs vertically, use four screws, and start at the top.

What comes first drywall or flooring?

When you're hanging drywall and installing new flooring, it's usually best to hang the drywall first and then save the floor for last.

Can drywall be stored on edge?

You can lean drywall vertically on its side if you plan on leaving it that way only for a few days or weeks, but for more long-term storage, you should try to store Sheetrock by stacking it flat.

Does drywall have to be flush?

The studs in your wall must be flush to hang drywall evenly. Uneven studs will result in uneven walls.

Do you stagger drywall on ceilings?

It's not necessary to stagger seams on ceiling drywall. However, because these joints are relatively difficult to finish – and tend to be noticeable in the finished product – it's a good idea to stagger the drywall panels to make the joints less visible.

How far should drywall screws go into studs?

As you finish, the head of the screw should be just barely recessed below the surface, no more than 1/8 inch.

Do you overlap drywall corners?

It doesn't matter for the walls, although it is standard practice to put drywall on the ceiling first so that the edges rest on the top edge of the drywall that you apply to the walls.