What is the metal plate in the bathtub for?

One of the most important is the overflow cover plate. As the name implies, the cover is designed to prevent water in the bathtub from overflowing. When water overflows from the tub, it can cause significant damage to the floor, other appliances, and the bathtub.

What is the metal thing in my bathtub?

A trip lever drain is a type of mechanism that is found in many bathtub designs. Essentially, the trip lever works as part of an apparatus that allows the stopper to be opened or closed, making it possible to retain water in the tub or release the water into the drain.

What is the circular plate in a bathtub?

That is the tub drain overflow plate, though it's actually above the drain, not the faucet. (The opening in this plate leads to a tube that prevents the tub from overflowing by allowing water to run out even if the drain in the bottom of the tub is stopped.)

How does bathtub overflow plate work?

The water that enters the overflow hole, goes down a pipe which is connected to the tub floor drain. With a well-functioning overflow drain, excess water will flow out the overflow hole, through the pipe and into the drain so as not to cause any damage to your bathroom or anything under or around the tub.

What is the drain at the top of the bathtub for?

The point of an overflow drain is to collect the excess water for your bathtub or faucet. The drain collects the water, preventing it from overflowing if you accidentally leave it on.

How To install a bath tub DIY method. Fitting steel bath and building secure frame for bath panels.

Why is there a hole under my bathtub?

Why is this hole there? It's to accomodate the bathtub drain, which connects to the tub in two places and runs horizontally right at about the level of the subfloor. Plumbers often use a chain saw or reciprocating saw to cut the hole and make it big enough so it's easy to install the drain.

What are the parts of a bathtub?

Why do tubs have an overflow?

A tub overflow functions as a “last line of defense” between the bathroom floor and the unexpected flood of an overfilled tub. It is an extra drain location to help remove water safely into the water waste line rather than allow it to spill out onto the floor or tub surround to warp or cause mildew buildup.

Where does the water go in a bathtub overflow?

The main drain is usually located at the bottom of your bathtub. The overflow component is located several inches under the rim. The two drains connect to various tubes that run from the bathtub and ultimately merge into one central pipe.

Can you fill the tub past the overflow?

Water will continue to fill the tub beyond the overflow drain, and the bathroom could flood if the shower is not turned off or a leak is not fixed.

How do you remove an overflow plate from a bathtub?

To remove it, place your thumbs at the bottom of the cover plate and press gently upward until the plate snaps free of the underlying mount and pops off in your hand. Depending upon whether you're troubleshooting, cleaning or upgrading, you can snap the same cover plate or a new one over the same mount.

How do bathtub stoppers work?

Toe-touch stoppers can be pushed in place to block the drain of your tub. To release, you simply push them again, and they pop back up. The most important part of this type of stopper is the rubber seal, which holds the water in the tub. The seal can wear out over time, but can be easily replaced.

Why won't my tub drain stay open?

Clean off both the plug and link with a toothbrush to clear away any built up sediment or calcium deposits that could be jamming them and preventing them from plugging the drain properly. Inspect the link connecting the plug to the overflow plate and replace this link assembly if needed.

Can you flip a tub overflow drain?

I simply unscrewed the drain plate, turned it upside down, and refastened it. Voila! The hole is now on the top of the plate. I have an extra 3 inches of water in the tub.

Does a bathtub have to have an overflow drain?

A bathtub does not have to have an overflow drain but a bathroom must have a mechanism to prevent flooding. Having a floor drain can be a practical alternative but insurance and building code considerations should be factored into your decision.

How full can you fill a tub?

Fill the tub until it is about 2/3 full, then turn off the water. Remember that once you step into the tub, the water level will rise. If you fill it to the very top, water is going to spill over the sides and create a spillage and water could go everywhere.

What are the tub hardware called?

Tub Spout — An output device through which water flows to fill a tub. The valve controls the flow. Two Handle Faucet — Two handle faucets feature separate handles to control hot and cold water temperature.

What is a shower diverter?

What is a shower diverter? If you have a combo bathtub and shower, your faucet handle has a way of changing the flow of water from the tub spout up to the showerhead, and the other way around. When you use this handle, you are activating the shower diverter, which if the valve behind the wall that directs the water.

What is a diverter pipe?

If you have a shower-tub combination in your bathroom, the shower diverter valve is what allows you to divert the water back and forth between the tub faucet and the showerhead. Though they are typically very simple devices, shower diverters may malfunction and need replacing once in a while.

What is a bathtub trap?

A trap is a common plumbing mechanism used near sinks, toilets, tubs, and other appliances to stop sewer gases from reentering your home. The trap is usually a bent pipe that captures water in the bend. This water stops incoming sewer gases, but allows outgoing gases to pass through.

Does a tub have a trap?

Does a bathtub need a P-Trap? Yes, you should always install a P-Trap as part of the plumbing of a bathtub or any other wastewater drain system. Failure to include a P-Trap could result in foul smells, harmful gases, and small animals entering through your tub's drain.

Do baths have traps?

Bath traps, a type of “slab leave-out”, are located under bathtubs. Why leave a big hole under a bath tub? Generally these openings are left for the convenience of plumbing contractors in case the plumbing needs to be moved or serviced.