What is the difference between pusher and non pusher mechanical seal?

Pusher seals utilize a dynamic secondary seal which moves axially with the major seal face. Non-pusher seals have a static secondary seal which stays stationary against the shaft or sleeve.

What is a pusher mechanical seal?

A pusher-type seal consists of a primary sealing ring assembled with an 'O' ring and springs which force the sealing liquid across the face and keep it from leaking to the ID side of the seal. The dynamic O-ring is designed to be pushed axially along the shaft.

What are the different types of mechanical seals?

What is the difference between balanced and unbalanced mechanical seal?

A seal with a balance ratio less than 100 percent is called a balanced seal. A seal with a balance ratio greater than 100 percent is called an unbalanced seal. Most balanced seals have a balance ratio between 60 and 90 percent. Most unbalanced seals have a balance ratio between 110 and 160 percent.

How do I choose a mechanical seal?

Part 2- Types of mechanical seal based on design- Balanced vs Unbalanced, Pusher vs Non-Pusher

What is a Type 1 mechanical seal?

Suitable for a wide range of service conditions ranging from water and steam to chemicals and corrosive materials, the Type 1 mechanical seal is ideal for use in pumps, mixers, blenders, agitators, air compressors, blowers, fans and other rotary shaft equipment.

What is the difference between single mechanical seal and double mechanical seal?

A single seal has two faces, while a double seal has four. A double seal divides faces into rotating and stationary. Single seals use the pump's fluid as a lubricant, while double seals have a dedicated buffer or barrier liquid.

How are mechanical seals measured?

To determine the size of a component mechanical seal, measure the inside diameter of the seal face, the length of the spring, and diameter and thickness of the stationary seat.

What is reverse balance seal?

Product Description. Reversed Balanced Pusher seals. Multiple spring Reversed Balance Mechanical Seals are externally mounted internally balanced multiple spring seals. the unique feature of this type of seals is that, it eleminated the shaft step or sleeves for balancing.

What is a mechanical seal balance diameter?

For many seals, the balance diameter can be estimated from the shaft size as follows: Classic rotating seal: shaft diameter plus 1/2” to 5/8” Inverted rotating seal (made into stationary seal): shaft diameter plus 5/8” to 1” Stationary seal: shaft diameter plus 5/8” to 1”.

What is a Type 21 mechanical seal?

General-duty Elastomer Bellows Shaft Seal

The Type 21 is ideal for use in centrifugal, rotary and turbine pumps, compressors, chillers and other rotary shaft equipment. It is also commonly used by the wastewater and water systems industries for applications such as waste treatment, potable water and HVAC.

What are the two main parts of a mechanical seal?

A stationary ring (usually the stationary seat) arranged in the stationary part (casing) Secondary seal (usually O-ring) between these parts.

What are the three basic parts of a mechanical seal?

Typically, a mechanical seal contains:

Secondary static seals, V-rings, O-rings or wedges. Static seal or stationary component.

What is non pusher seal?

Non-pusher seals have a static secondary seal which stays stationary against the shaft or sleeve. Defined by the secondary seal type: o-ring or polymer wedge versus bellow, rubber or metal.

What is seal hang up?

Hangup. Loss of axial movement, or seal hangup, is caused when leakage accumulates and hardens beneath the “floating” element. In most seals, this is the rotating element. Hangup is a particularly troublesome problem in high temperature seals because any leakage tends to form “coke”.

What is a seal in engineering?

A mechanical seal is a device that helps join systems or mechanisms together by preventing leakage (e.g. in a pumping system), containing pressure, or excluding contamination. The effectiveness of a seal is dependent on adhesion in the case of sealants and compression in the case of gaskets.

Why do mechanical seals leak?

If there are no fluids available to lubricate, the seal runs dry which causes extra friction and heat. The seal will burn or melt and become damaged, which causes fluid leakage due to the pressure. Even a few seconds of dry running can cause heat cracks or blisters, which leads to a leaking pump shaft seal.

What is seal chamber pressure?

The seal chamber pressure is a function of wear ring clearance as well as size and location of the balance holes. Two Stage Horizontal Pumps. Impeller arrangement can have two. configurations: 1.)

How long should a mechanical seal last?

Most seal manufacturers say that operation of the seal at one of these limits will result in a minimum life span of two years; three years with some seal types such as those specified in Standard API 682.

What is the difference between barrier fluid and buffer fluid?

When this fluid is unpressurized, it forms a buffer between the pumped fluid and atmosphere and is commonly referred to as a buffer fluid. When pressurized, it forms a barrier between the pumped fluid and atmosphere and is known as a barrier fluid.

What is Tandem mechanical seal?

Tandem seals are two single seals mounted in the same direction. Tandem seals are used for toxic or flammable liquids that require a buffer or safety zone. If the inboard seal fails, a high pressure alarm will activate to provide a warning that the inboard seal has failed.

Do mechanical seals need lubrication?

Lubrication is necessary for proper mechanical seal installation. Lack thereof can damage o-rings or rubber bellows on the seal, causing them to tear, or roll.

What is the most common mechanical seal?

Probably the most popular choice of secondary seals for mechanical seal faces is o rings however there are other forms of secondary seals but the standard form and availability of o rings makes them ideal candidates for secondary seals.

What is the difference between gland packing and mechanical seal?

When considering gland packing vs mechanical seal solutions, mechanical seals are the best for minimizing sleeve damage. Packing seals are removed and replaced much more often than mechanical seals, which causes considerable wear and tear to the pumps as they are disassembled and reassembled.

How many seals are in a centrifugal pump?

Double mechanical seal - This is where two mechanical seals are used within a pump. The first seal retains the fluid within the pump as per the standard mechanical seal above. The second seal contains a barrier fluid to ensure the faces are kept clean and are lubricated preventing failure.