What is the B button on gas meter?

Once you get to this option, you should be able to see your electricity reading. To take an export reading from your Aclara SMETS2 electricity meter: Press the B button to wake the screen up. After the screen lights up, press the B button several times until you see a message that starts with either 'Total' or 'TOU'.

Do I press A or B on my gas meter?

press the A button. press the A button again until you see 'METER INDEX' and numbers followed by 'M3' write down the number from left to right. ignore any zeroes at the beginning and any numbers after the decimal point.

What are the A and B buttons on my gas smart meter?

If your meter has an 'A' and 'B' button, press 'A' until you get to TOTAL ACT IMPORT. The number below this is your electricity reading. Your meter might have three buttons to the side of the display. If this is the case, just press the middle button, and the display will show your reading below the 'IMP' on screen.

How do I read my gas meter?

Why is my British Gas smart meter not connecting?

If your smart energy monitor stops working check your power cable is inserted correctly and your power supply is switched on at the wall. If it's still not working, try using fresh batteries. If batteries fix the issue, then the problem is with the cable.

How to gas rate a SMETS2 smart meter ( similar to an E6 Electronic meter)

What does the B button do on a smart meter?

If you pay a single rate

To read the meter: press the white B button - the screen will light up. wait until the screen says 'meter boost' - press 'A' to select 'no' and you should see numbers followed by 'KWH'

Why is my smart meter not connecting?

If your smart energy monitor stops working, check the mains power cable is inserted correctly and that your power supply is switched on at the wall. If it's still not working, try using batteries. If batteries don't help, then the problem may be with your smart meters.

Why is my gas reading so high?

High gas bills may be due to a gas meter that is incorrectly recording the amount of gas you are using, but this is unusual. While there is no simple way you can test whether your meter is accurate, if you are concerned about your meter readings, contact your energy supplier.

How do I reconnect my gas meter?

If you're reconnecting your gas meter, make sure all gas appliances are off before you start. Press any button on the keypad of your meter on the wall. You'll see the OFF message change to READY (this can take up to 30 minutes). When it does, press A, then B, to reconnect.

Why is my gas meter not showing a reading?

If your gas meter screen is blank

Your gas meter is battery powered so to save power the screen will be blank. To take a reading from your gas meter, press the round button between the two arrowed buttons and the reading will show on screen. After 30 seconds the screen will go blank again.

How do I reset my British gas electric meter?

Restore my electricity supply using my meter

Press button 'A' to enter the main menu. Press button 'A' to enter the status selection. Press button 'A' to select prepayment status. Press and hold button 'B' to restore your supply.

Can I phone British Gas with meter reading?

Give a meter reading

If you would like to speak to a human, you can still call British Gas customer service directly and submit your meter readings over the phone.

What a smart meter looks like?

A smart meter looks a lot like the standard gas and electricity meter that you would have already. Smart meters come in different shapes and sizes however they tend to have buttons which when pressed, will allow you to cycle through the several displays.

Is electricity cheaper at night British Gas?

Lowest electricity rates overnight

Get our lowest electricity rates between 12am and 5am - perfect for scheduling your electric vehicle charges to save money.

How do I pair my smart meter?

Press and hold the power button on the back of your smart meter display to turn it on. To turn it off, press and hold the same button for five seconds. Each time you turn the smart meter display on, it will show 'Welcome to IHD2' then 'Attempting to pair'.

How do I reset my smart meter?

To reset it it turn it right off by holding down the power button for 10 seconds and then power it back on again, it should work.

How do I reconnect my smart meter to WIFI?

How do you read a digital meter?

Read the dials from left to right. If the pointer is between the two numbers, always take the lower number. If the pointer is directly over a number, write down that one. If the pointer falls between 9 and 0, write down 9 and reduce the reading you've already taken for the dial on it's left by one.

How does a gas meter work?

A gas meter is driven by the force of the moving gas in the pipe, and also turns faster as the flow increases. Each time the dial with the lower value makes one complete revolution, the pointer on the next higher value dial moves ahead one digit.

How do I read my prepayment gas meter?

The default display on your prepayment meter will show you what your current credit level is. To view your meter reading, simply push the button located on the front of your gas meter. Doing this will change display to show your reading. From this point just note down the reading as normal.