What is MTA pulp therapy?

MTA was used as pulp-capping

pulp-capping

An alternative procedure to extraction or endodontic therapy is pulp capping, in which a medicament is placed directly over the exposed pulp (direct pulp cap), or a cavity liner or sealer is placed over residual caries (indirect pulp cap) in an attempt to maintain pulp vitality and avoid the more extensive treatment ...

https://www.ncbi.nlm.nih.gov › pmc › articles › PMC2856472

Keys to Clinical Success with Pulp Capping: A Review of the Literature

material after partial pulpotomy to preserve the vitality of the pulpal tissues in two cases. Follow-up examinations revealed that the treatment was successful in preserving pulpal vitality and continued development of the tooth.

What does MTA do to pulp?

The researchers have reported that MTA induces proliferation of pulp cells,41, 42 it stimulates osteoblasts to release interleukins⁴ with formation of hard tissue,⁴³ and an interface with the dentin that is very similar in composition to the hydroxyapatite.

Why MTA is used in pulp capping?

Various materials have been used as pulp-capping agents, including bonding agents, cements, resin, calcium hydroxide, and many others [12]. Currently the most promising materials are calcium hydroxide and MTA, since both materials have the capacity to induce bridging of the pulp surface with reparative dentin.

What does MTA do for teeth?

MTA is used for creating apical plugs during apexification, repairing root perforations during root canal therapy, treating internal root resorption, and pulp capping.

What is MTA in endodontics?

Mineral trioxide aggregate (MTA), composed mainly of tricalcic silicate, tricalcic alluminate, bismuth oxide, is a particular endodontic cement. It is made of hydrophilic fine particles that harden in the presence of dampness or blood.

Vital Pulp Therapy: Adult Pulpotomy with Dr. Nasseh

Is MTA a liner or a base?

MTA provides a higher incidence and faster rate of reparative dentin formation without the pulpal inflammation. MTA Plus material is also indicated for base and liner in vital pulp therapy. In root-end filling after apicoectomy, the anti-washout agent (chitosan or gelatin) is useful to prevent from MTA washout.

What is the difference between MTA and calcium hydroxide?

MTA is more effective and superior comparing the Calcium Hydroxide as a direct pulp capping material, showed higher success rate with favorable outcomes in maintaining long term tooth vitality and easier to use in pulp capping. MTA is less toxic, less pulpal inflammation capping compared to Calcium Hydroxide.

How long does it take for MTA to set?

It has been reported that MTA sets slowly approximately 3-4 hours in clinical conditions (3, 25). Long setting time of MTA can cause clinical problems.

Does MTA bond to tooth?

Nowadays, the material that offers the best sealing characteristic in the field of endodontic treatment is the mineral trioxide aggregate (MTA), nevertheless, this material necessities an adhesive bonding agent to perfectly join to the dental surface.

What are the advantages of MTA?

MTA has the advantage of being less soluble than calcium hydroxide and offers an enhanced seal due to its setting expansion which hermetically seals the pulp space, preventing bacterial contamination from the outside.

What is MTA pulpotomy?

MTA may be used as an alternative pulpotomy agent in immature teeth with pulp exposure to stimulate pulp healing with dentin bridge formation and complete root formation. But, discoloration following MTA pulpotomy appears as a major clinical complication.

Can we do obturation with MTA?

It is clear that MTA resists bacterial leakage to a higher degree than gutta-percha and sealer when used as an obturation material. These findings also demonstrate that the placement of MTA is technique-sensitive, and protocols for proper obturation and condensation must be observed.

Is MTA toxic?

At the 24-hour period, white MTA produced the lowest toxicity, statistically comparable to the control group (p > 0.05), whereas the white and gray CER cements presented the highest cytotoxic effects on the fibroblast-like MDPL-20 cells.

How do you put a MTA on a root canal?

The MTA powder is mixed with sterile water, and the mixture is placed in contact with the exposure using a Dovgan carrier (Figure 2). Compress the mixture against the exposure site with a moist cotton pellet. Place a moist cotton pellet over the MTA and fill the rest of the cavity with a temporary filling material.

Do you cure MTA?

Light-curable and dual-cure MTA products contain resins which dilute and inhibit the MTA's bioactivity. Resins never cure 100%. Uncured resin leaves cytotoxic monomers in the MTA-resin matrix and in contact with the pulp. Resins shrink during curing; they are not dimensionally stable.

Is MTA light cured?

To protect the MTA during its setting, a light cured glass ionomer (Fuji 2 LC GC America, Alsip, IL) is injected precisely over the MTA site with a Skini Syringe and Endo-Eze canula (Ultradent/Clinical Research Dental) (Figs.

How do I remove MTA?

Removal of MTA from dentin by applying 37% hydrochloric acid (HCl) to reduce microhardness and push-out bond strength.

What is MTA made of?

Mineral trioxide aggregate (MTA) is composed of Portland cement, with 4:1 addition of bismuth oxide added so that the material can be detected on a radiograph. The cement is made up of calcium, silicon and aluminium. The main constituent phases are tricalcium and dicalcium silicate and tricalcium aluminate.

Is MTA used in primary teeth?

MTA as a pulpotomy agent has shown favorable results in case of primary molars. There is limited literature available regarding its use in primary incisors. However, the success of vital pulp therapy with MTA depends on proper case selection and technique of management of the tooth than the material itself.

Can MTA be mixed with saline?

The high sealing ability of MTA in combination with normal saline has been supported by all these studies. Also our study proved the superiority of the combination of MTA with normal saline compared to 5% CaCl₂ and KY Jelly.

Can MTA be used in indirect pulp capping?

Indirect pulp capping accompanying complete caries removal exhibited a satisfactory success rate in the treatment of deep carious lesions. Both Ca(OH)₂ and MTA were found to be clinically effective at 24 months posttreatment.

How do you mix MTA dental?

Manipulation and setting reaction of MTA The MTA paste is obtained by mixing 3 parts of powder with 1 part of water to obtain putty like consistency (distilled water, local anesthesia, normal saline).

Is Biodentine same as MTA?

Biodentine is comparatively a new biomaterial claimed to have properties comparable to mineral trioxide aggregate (MTA). Biodentine and MTA are effectively used for direct pulp capping (DPC), and they are capable of regenerating relatively damaged pulp and formation of hard dentine bridge.

What material is used for pulp capping?

Two types of pulp-capping materials, calcium hydroxide and mineral trioxide aggregate, have been most commonly used in clinics, and an adhesive resin has been considered a promising capping material.

What is Dycal composition?

Dycal® is a paste-paste calcium hydroxide dental cement uses as pulp capping and liner in dentistry. First paste (base paste) contains titanium dioxide and barium sulphate in glycol disalicylate and second paste (catalyst paste) contains calcium hydroxide, zinc oxide and zinc stearate in ethyl toluene sulphonamide.