What insulation has the highest R-value per inch?

Vacuum insulated panels have the highest R-value, approximately R-45 (in U.S. units) per inch; aerogel has the next highest R-value (about R-10 to R-30 per inch), followed by polyurethane (PUR) and phenolic foam insulations with R-7 per inch.

Which type of insulation has the highest R-value?

In the construction industry, how well a particular type of insulation resists the flow of heat is represented by a value called “R.” Among insulation types, rigid foam panels have the highest R-value per inch.

What is the thinnest insulation with highest R-value?

Aerogel insulation offers the highest R-value of any insulating material at less weight and thickness—ideal for construction, refineries, pipelines, and thin-gap thermal barriers.

What rigid insulation has the highest R-value per inch?

Polyisocyanurate: Known as polyiso for short, polyisocyanurate foam has the highest R-value per inch (R-6.5 to R-6.8) of any rigid insulation. This type of rigid foam usually comes with a reflective foil facing on both sides, so it can also serve as a radiant barrier.

Which of the following materials has a the highest R-value per inch of thickness?

Vacuum insulated panels have the highest R-value, approximately R-45 (in U.S. units) per inch; aerogel has the next highest R-value (about R-10 to R-30 per inch), followed by polyurethane (PUR) and phenolic foam insulations with R-7 per inch.

Busting R-value insulation MYTHS

Is r40 insulation good?

It is a rigid material that helps reject lots of water, adds wall racking strength as well as impact resistance. Closed-cell foam has a higher R-Value than any insulation, it ranges from 5.0 to 7.0 per inch. Regarding the thickness of the spray foam insulation, it depends on certain factors.

What is the R-value of 1 inch thick STYROFOAM?

STYROFOAM extruded polystyrene insulation is rated at an R-value of 5.0 per inch at 75°F.

What is the R-value of 2 inch rigid foam?

With an R-value of 13.1 for a 2" thick sheet only two 2" sheets are required to achieve R-25. 2. Extruded polystyrene or XPS (foam is usually pink or blue) XPS has an R-value of 5 per inch of thickness requiring 5" of insulation to achieve R-25.

What is the R-value of 1 inch spray foam?

This microscopic difference in the two products creates a dramatic difference in performance. Closed cell spray foam has an R-value of R-7 per inch. In comparison, open cell spray foam has an R-value of R-3.8 per inch. Additionally, the materials have decidedly different densities.

What is the R-value of 2 inch blue foam?

A wall utilizing STYROFOAM T-MASS Technology with a 2-inch exterior layer and a 4-inch interior layer of concrete along with a 2-inch layer of STYROFOAM extruded polystyrene insulation would result in a material R-value of approximately 11.33.

What is the R-value of aerogel insulation?

It's quite thin, breathable, fireproof, doesn't absorb water, and is very strong considering it doesn't weigh much. What makes it such a great insulator is its low thermal conductivity (14 mW/m-K) and results in an R-value of 10.3 per inch, which is twice as much as rigid foam board.

What is the most efficient insulation?

Fiberglass insulation still allows for airflow into the attic. Spray foam insulation is the most energy-efficient insulation to create an air barrier in the attic. Certain spray foams can expand up to 100 times its original size, so it fills all of the nooks and crannies in the attic.

What is the highest R-value for 6 inch batt insulation?

Fiberglass Insulation Batts

Fiberglass blankets or rolls provide an R-value of up to 3.2 per inch, so a 6-inch fiberglass batt may achieve an R-value of 19.2, and some high-performance products are rated at R-21.

What is the R-value of 4 inch STYROFOAM?

STYROFOAM extruded polystyrene insulation is rated at an R-value of 5.0 per inch at 75°F.

What is better foam or fiberglass insulation?

Spray foam insulation has a higher R-value than fiberglass, making it a better insulator. Another difference between them is that spray foam is watertight while fiberglass cracks under moisture. However, installing spray foam requires a professional while fiberglass is easy to install yourself.

What is the R-value of Rockwool?

While fiberglass insulation is capable of offering an R-value of about 2.2 to 2.7 per inch of insulation, Rockwool has an R-value between 3.0 to 3.3 per inch of insulation.

What is the R-value of aluminum foil?

According to ASHRAE, when just a little condensation is visible on aluminum foil, the emissivity can reach 0.2 to 0.3, which would decrease that R-value down to R-3.86.

What is the R-value of XPS insulation?

XPS Data Summary:

R-value: 4.7 per inch.

What is the R-value of rigid foam board?

Rigid foam R-values range from R-1 for 1/4-inch thick sheathing panels to R-15 for 3-inch thick panels. R-value is not entirely a function of the thickness of the material, as the facing material and type of foam used will affect the R-value of the material.

How many inches of insulation is R40?

Fresh, new cellulose loose-fill insulation has an R Value of 3.1 to 3.8 per inch. You see, cellulose insulation has a higher R value per inch than loose fill fiberglass insulation. We are a cellulose installer. To achieve R-40, we install 12” of cellulose insulation.

What is R28 insulation used for?

Use this fibreglass attic insulation between wall studs, floor joints, on the ceiling and in attics. It offers effective resistance to heat transfer to improve the energy efficiency of your home.