What happens if you over tighten axle nut?

No. Over tightening won't put more of a strain on the bearings in this sort of design. You should've torqued those nuts down quite a bit.

What happens if wheel bearing nut is too tight?

Once greased up and put back into place, wheel bearings need to be tightened in a very specific way. If this is not done properly, they can become too tight and that will cause excessive wear to the bearing itself, ultimately causing it to fail.

How tight should the axle nut be?

Expert Reply: The nut on the spindle should be tightened until snug, with no side-to-side play in the hub and then backed off slightly, about maybe a 1/8 of a turn.

What happens if you overtighten hub nut?

It's possible to damage the wheel, rotor, and hub assembly. The wheel can come off if over-torquing the nuts/bolts is done.

What happens if axle nut is loose?

Loose axle nuts can become a serious problem. When the axle nut is loose it allows the wheel bearing to shift back and forth which can cause damage and cause the wheel bearing to fail. When the axle nut is installed properly it is staked so it cannot come back off, though it could still become loose.

Wheel bearing nut over tightened

What does a loose axle sound like?

1. "Clicking" Noises When Turning. Though it's sometimes described as a loud click and sometimes described as a pop, this noise is unmistakable once you hear it. It presents itself when you turn the vehicle, and it's due to the loose joints of a worn CV axle.

Can you drive on a loose axle?

While you might be able to limp away if the axle is only slightly bent, it is never a good idea to drive on a damaged axle. If the axle fails completely you can lose control of the car. Common damage to the axles include: Leaking CV boot You're ok for a little while, but get it fixed very soon.

Can you over tighten lug nuts by hand?

Can you over-tighten your lug nuts by hand? Sure you can. If it's not just your car that's jacked up. If you have the necessary muscle, you could tighten the nuts more than the specifications call for.

What is the axle nut torque spec?

Generally, jam nuts less than 2-5/8" should be torqued to 200-300 lbf-ft; nuts 2-5/8" and over should be torqued to 250-400 lbf-ft. See chart for exact torque specification. The final step is to use a dial indicator to verify the end play or free movement of the tire and wheel assembly along the spindle axis.

What torque should wheels be?

What is your car's torque value? The optimum torque value for your car or mounted rims can be found in the vehicle manual. It depends on the car model, rim size, design (aluminium or steel rims) and number of bolts. It is normally between 110 N⋅m and 120 N⋅m.

Do you need to torque axle nut?

Proper torque is critical for two reasons. First, it secures the axle nut so it won't work itself loose and back off. Second, the proper torque keeps the correct load on a hub assembly needed for longer bearing life. Torque specifications can be different, even for the same hub, if it's multiple applications.

How much wheel bearing play is too much?

One way to check wheel-bearing play is to raise the wheels off the ground and rock the tires in and out while watching for any looseness. As a rule, there should be no play on most FWD cars, but up to . 010 inch of play in the front bearings may be acceptable on RWD cars and trucks with adjustable bearings.

Can you over pack wheel bearings?

If too much grease is “packed” into the bearing and the cavity, this grease will be pushed out when the wheel spins, and could easily ruin the brake shoes. In addition, the wheel bearing could actually overheat. Repacking wheel bearings is an easy job, and should be part of the routine maintenance of the vehicle.

Is it OK to reuse axle nut?

The old nut will not hold the proper torque a second time. Don't even think about “re-deforming” the old nut in your bench vise—it won't work. New axle nuts cost about $3 and ball joint nuts usually less than $1. Your family's safety is worth far more than that.

What is the torque specs for the spindle axle nut?

For one-piece spindle nut systems, torque the nut to a minimum of 300 ft-lbs. Do not back off the spindle nut. Engage any locking device that is part of the spindle nut system. If the locking device cannot be engaged when the nut is at 300 ft-lbs, advance the nut until engagement takes place and the nut is locked.

Can over tightening lug nuts warped rotors?

Overtightened Lug Nuts and Brake Rotors

Over-torquing a wheel can result in a warped brake rotor and possible hub flange damage. Rotors get extremely hot and improper, and over-torquing a wheel can result in warpage as the rotor heats up and cools back down in service.

What does the axle nut do?

Axle nuts are pieces of hardware that are used to help secure a wheel to an axle. The axle is a rotating shaft that helps secure the wheels to the rest of the vehicle and facilitate movement, and the axle nuts will be secured to lugs that are attached to either end of the axle.

How can you tell if your axle is bad?