What does a loose flex plate sound like?

Here are some of the warning signs of a bad flex plate: Clunking, grinding, chirping, or rattling noises from rear of engine when engine is idling. Knocking noise when engine is shifted into drive or reverse. Heavy vibrations felt through the driver's seat when driving at normal speeds.

How do I know if my flex plate is bad?

What does a warped flexplate sound like?

These features illustrate flexplate is warped, provided starter works in a proper way and can be ruled out. Listen for rhythmic clunking or grinding noise when engine idles in neutral or park, or idles in gear with foot on brake pedal.

What does a loose flywheel sound like?

Loose flywheel or flexplate bolts make a rattling or knocking sound that changes with engine speed. It's heard behind the engine, where it mounts to the transmission bellhousing.

What makes a flex plate go bad?

The following causes for cracked flexplate failures: 1) Out of balance engine or torque converter. 2) Bad starter drive can cause teeth or ring gear to wear rapidly or break off. Teeth can also break when engine is running and starter is engaged.

Knocking engine noise... flex plate or engine ?

How much does it cost to fix a flex plate?

You have to disassemble the parts, repair the flexplates, or replace them and reassemble that entire part once again. The average cost of flexplate parts is between $185-$195 just for the plate itself. Labor cost, cost of oils, and other additional charges can raise this process up to $1500 or more.

What happens if flexplate breaks?

When a flexplate cracks, it often produces a loud knocking noise as it rotates. The sound is very similar to a bad engine rod and is often misdiagnosed. Removing the bolts to the torque converter and sliding it back into the transmission will often reveal the real problem.

How do you test a flexplate?

What does a broken torque converter sound like?

Whining or rattling noise

Likewise, when a vehicle torque converter fails, the car will give a bad torque converter noise–a whining or whining sounds like a power steering pump with little or no fluid in it.

What is the difference between flexplate and flywheel?

The flywheel is found primarily in vehicles that have a manual transmission, whereas the flexplate is found in automatic transmission vehicles. Both of these components are typically heavy, but the flexplate is much thinner and therefore lighter than the flywheel.

What are the symptoms of a loose torque converter bolt?

When the torque converter starts malfunctioning, you may feel shuddering and even slipping in overdrive. You usually notice your car shuddering because it feels like it's vibrating. Your car will vibrate even when you're not going very fast. The shuddering makes the car lag and is very noticeable.

How long does it take to replace a flexplate?

The entire operation can take anywhere from 6-8 hours. And most mechanics have an hourly rate of about $90-$110. Add to these costs the price of a flexplate itself and that of flex plate seals and oils, which would range from $185-$195.

How do I know if my torque converter is broken?

Can a transmission make a knocking sound?

The sensors in the transmission are incorrectly regulating shifting information or your speed… Many transmissions in cars nowadays are controlled by computerized sensors. Often clunking noises can occur because the sensors send incorrect shifting or speed information, creating a problem due to incorrect regulation.

Why is my car making a whining noise when accelerating?

While the transmission is the most likely cause, whining while accelerating can also be caused by low power steering fluid or more serious damage like faulty alternator bearings, a malfunctioning water pump, a broken piston or a bad AC compressor.

Why does my transmission whine when I accelerate?

A whining sound from your vehicle's transmission is generally indicative of a fluid-related issue. It is quite common to hear a noise of this nature, when a transmission's fluid level is reduced beyond capacity, or when a transmission fluid pump begins to fail.

Why is my transmission whining?

If the whining gets higher with the revere, it means that the fluid line of the transmission has been clogged. In most cases, a clogged fluid line points to a more significant issue. On an automatic transmission, if the whine gets louder when in gear, it points to a problem with the torque converter.

What does the flex plate do?

A flexplate (or flex plate) is a metal disk that connects the output from an engine to the input of a torque converter in a car equipped with an automatic transmission. It takes the place of the flywheel found in a conventional manual transmission setup.

Is a flex plate a flywheel?

Basically a flywheel or flex plate is the round metal disc shaped component that transfers power from the engine to the transmission. A flywheel is usually referenced to a car with a standard transmission,and a “flex plate” is used with automatic transmissions.

Where is a flexplate located?

A flexplate is mounted to the crankshaft and connects the output from the engine to the input of a torque converter. Torque converters replace the clutch of a manual transmission.

Why does my flywheel keep cracking?

1) Bellhousing bolts loose. 2) rust build up between the torque converter centering shaft and the crank. 3) Bad converter. 4) missing or poor design flexplate hold down ring( not sure the proper name but it is a ring that goes between the flexplate and the bolts that hold it to the crankshaft.