Should you put plastic between insulation and drywall?

Without poly beneath the drywall, water vapor hits the drywall and diffuses through to the drier (in summer) indoor air. By installing a sheet of poly there, you cut off that drying mechanism and water that finds its way into walls can stay there longer and do more damage.

What should I put between drywall and insulation?

Between the insulation and the sheetrock I staple 6 mil plastic; I was taught this a few years ago, and it seemed to make sense (as I recall, the reasoning was the the plastic forms a vapor barrier, which keeps interior moisture from getting “trapped” in the insulated walls).

Should insulation be covered with plastic?

Plastic isn't recommended in this situation because it would create a second vapor barrier that can trap moisture and result in condensation and mold. Craft paper would have the same problem, this is what is most likely on the other side of the insulation for the vapor barrier you want.

Should you put plastic over ceiling insulation?

Plastic vapor barriers should only be installed in vented attics in climates with more than 8,000 heating degree days. You can forego the plastic and use a vapor retarder (kraft-faced insulation or latex ceiling paint) in all other climates except hot-humid or hot-dry climates.

Is a vapor barrier necessary behind drywall?

No, you don't need a vapor retarder, Class I or otherwise. By the time you paint the drywall, though, you've brought it into the Class III vapor retarder range (between 1 and 10 perms), and even less water vapor will diffuse through. Seal the air leakage pathways.

Why you must have Vapor Barrier

Do you need a vapor barrier on wall insulation?

After the insulation is in place you will want to add a vapor retarder, sometimes called a vapor barrier, if you need one. Not every wall does. A vapor retarder is a material used to prevent water vapor from diffusing into the wall, ceiling or floor during the cold winter.

When should you not use a vapor barrier?

Can plastic be used as a vapor barrier?

Plastic, specifically 6-mil polyethylene plastic, is the most commonly used vapor barrier. Plastic has a very low permeability rating, which means water, in its gaseous or liquid state, does not travel through it.

Do vapor barriers cause mold?

One of the more common problems with crawl spaces that do not have a crawl space vapor barrier system is that they create high moisture levels, which may result in mold growth – as dampness creates the ideal environment for mold growth.

Can you put vapor barrier on both sides of insulation?

Avoid installing vapor barriers on both sides of a structure. Walls and ceiling cavities should ideally have the ability to dry out in one direction if the other side is constructed to prevent moisture penetration. Seal all wall cracks and holes in the wall being vapor-proofed to block air gaps.

What do you cover insulation with?

After the insulation is installed, it is necessary to cover it up with a vapor barrier so the glass fibers are not inhaled. The best vapor barrier to use is roll of plastic sheeting. This vapor barrier is easy to install and does an excellent job.

Is it safe to leave insulation uncovered?

"Fiberglass insulation should never be left exposed in an occupied area, according to the American Lung Association," says ALA's Godfrey. "Exposed fiberglass insulation, once in the air, does cause respiratory reactions, such as dry, scratchy throat and coughing, as well as acting as a skin and eye irritant.

Should I tape insulation seams?

Yes, you tape any insulation's lateral seams, especially any fluffy stuff... aluminum HVAC tape lasts the longest. The fluffy stuff really only works best in dead air space. Which also means the un-faced side (where you don't tape anything).

Can I use Tyvek as a vapor barrier?

Is DuPont^™ Tyvek^® a vapor barrier? No, DuPont^™ Tyvek^® is not a vapor barrier. It is made with unique material science to keep air and bulk water out while allowing moisture vapor inside walls to escape.

Does ceiling insulation need a vapor barrier?

Fiberglass Insulation

Like other batt-type insulation, fiberglass has a predictable R-value if not compressed but is difficult to fit around obstacles without leaving gaps. In most climates, it needs a vapor barrier.

What is the difference between a vapor barrier and a moisture barrier?

Moisture barriers function to help in preventing water from entering inside of the wall cavity. On the other hand, vapor barriers basically prevent water vapor from the interior of the house to filter through the wall and condense on the warm side of the insulation.

Should a house have a vapor barrier?

Vapor barriers protect against mold and rot inside structures by preventing condensation and moisture from building up and damaging building materials. If a home is being built in a very humid climate, a vapor barrier can be an essential source of protection from problems caused by excess moisture.

Are moisture barriers good?

A moisture barrier offers more protection than you might think. If you don't prevent moisture build up in your home, major problems will arise. You want to keep moisture under control and out of your home. Protecting your home from water vapor can be the difference in it lasting ten years or a hundred.

How thick should a plastic vapor barrier be?

Vapor barriers should be at least 6 mil in thickness to effectively cover the area and create a moisture barrier. Triangle Crawl Space Solutions uses both a 6 mil material for simple vapor barrier installation and a thicker more durable 12 mil vapor barrier material depending on the budget and needs of the home.

Is paper faced insulation considered a vapor barrier?

There are two basic types of vapor barriers used with exterior wall insulation. The most common is paper-faced insulation. This type of insulation has a Kraft paper face with two flanges.

What side does vapor barrier go on insulation?

In order to prevent condensation from forming, a vapor barrier should be placed on the warm side of your insulation to stop warm, moist air from condensing on a cold surface inside your wall.

What happens if you don't have a vapor barrier?

The short answer is: if your wall doesn't have a vapor retarder, there is no need to worry. Builders worry way too much about vapor diffusion and vapor retarders. It's actually very rare for a building to have a problem caused by vapor diffusion.

Should I staple vapor barrier?

Tug and smooth the vapor barrier to ensure a completely smooth surface lacking wrinkles or gaps through which moisture and air may escape, defeating the vapor barrier's purpose. Staple through the plastic into the sole plate -- the horizontal board running under the studs – at bottom.

Does faced insulation need to be covered?

To satisfy building codes, most faced insulation must be covered with half-inch-thick wallboard or other code-approved material to reduce the chances of its igniting during a fire. There is a type of faced insulation approved for exposed installations.