Should I use shock or algaecide first?

While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.

Should I shock my pool before adding algaecide?

Algaecide should be used after each shock treatment, so it has a better chance to support your chlorine as it works its magic. Be sure to shock your pool first, then when the chlorine levels of your pool return to normal, add the correct amount of algaecide to several places around your pool while your pump is running.

Do you add algaecide before or after shock?

Algaecide should be added to your pool water on a weekly basis. Preventing algae is the key to fun in your pool. Algaecides act as a backup to your normal sanitization program and prevent algae from starting and growing in the pool. Algaecide should be added after every shock treatment.

How long after using algaecide can you shock?

How long after algaecide can you shock? You should wait at least 24 hours before shocking the pool after adding algaecide. After shocking, always check the free chlorine and total chlorine levels because they could increase very high if you do not wait long enough before shocking.

Should you run the pool filter after shocking?

A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.

The TRUTH About Using ALGAECIDE In Your POOL | Swim University

When should you put shock in your pool?

The ideal time to shock your pool is in the evening after all swimming is complete. In the evening because the sun will not be boiling the chlorine out of your pool, and after everyone is done swimming because shocking is going to bring the chlorine level up to a level that may be irritating to skin and eyes.

What chemicals should I balance first in my pool?

Total Alkalinity (TA) is the first thing you should balance in your pool water. TA refers to the amount of alkaline material in the water. And since alkaline is a pH stabilizer, the number of alkaline substances in water will affect the pH balance. The ideal Total Alkalinity range for pool water is 80 – 120 ppm.

Why is my pool still green after shock and algaecide?

Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.

What happens if you put too much algaecide in a pool?

The presence of too much algaecide can lead to a foamy pool water. Small bubbles will begin to be produced as the water is pushed through the return jet and back into the pool. Do not confuse these bubbles and foam with another common problem, which is air in your pool lines.

Can you put algaecide and shock in the pool at the same time?

Shocking your pool and adding an algaecide to the water are two ways to get rid of the sickly green color caused by algae growth, but you shouldn't do these things at the same time. Chlorine combines with the algaecide ingredients and renders them useless.

Should I run the filter after adding algaecide?

Add a dose of algaecide, bring your chlorine level high by shocking, and run the filter continuously until the problem clears. The next day you should vacuum up the dead algae and backwash your filter. Algae thrives in hot weather and in pools with low or no chlorine.

What do you do after you shock your pool?

Answer: After shocking the pool, it will need filtration and circulation. Run the pump as much as possible. Keep the filter clean (daily) until the water runs clear. Be sure to brush the pool often during this process as above-ground pools do not have drains at the bottom.

Will algaecide help a cloudy pool?

5. Can I Use Algaecide to Clear Cloudy Pool Water? You can use an algaecide to kill early stages of green algae that might make your water appear cloudy, but the best method of getting rid of algae is to scrub and clean your pool using a large leaf net, vacuum, and kill algae with liquid chlorine shock.

Can I add algaecide during the day?

In addition to properly dosing your water, it is also recommended that the algaecide be added in the morning on a bright sunny day for best results. Algae are plants and grow in the presence of sunlight. Adding algaecide during algae's best growth time will increase intake of the algaecide and make it more effective.

Does algaecide affect chlorine?

Algaecide also works together with chlorine, helping the chlorine to be more effective against algae and bacteria.

Can you vacuum algae out of a pool?

All you need to do is bypass the filter and pool vacuum for algae to the waste. However, this can only work if you have a multiport system or a waste line system in your cartridge filter. Vacuum the pool to waste after you have set up the waste, and the debris and algae will get out of your pool.

How long does it take shock to clear a green pool?

You need to raise the level of your chlorine – shock the pool – and maintain that high level until all the algae is dead. This may take 3 to 4 days.

Can I swim 12 hours after shocking pool?

After Shocking Your Pool

It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!

Will Shocking a pool raise the pH?

Pool shock.

Shocking your pool is important, but if you're using cal-hypo (calcium hypochlorite), it can raise your pool's pH levels. Don't stop shocking your pool, but do test all your chemistry levels consistently, especially after shocking.

Does Shocking a pool lower alkalinity?

Another cause for high alkalinity can be when you shock the pool. While this is performed to quickly rid the pool of pollutants, chlorine-based pool shock is highly alkaline, and can raise the water's total alkalinity level in the process.

How long do I wait between adding pool chemicals?

Wait times for adding pool chemicals

The wait times between adding pool chemicals is usually around 10 minutes each, as that is also sufficient time for the chemicals to mix in the water. Users also under normal conditions can swim roughly 10 minutes after adding chemicals.

Should I shock my pool every week?

It's often recommended to shock your pool once a week. If you don't do it every week, you should at least do it every other week. This is necessary to maintain your pool's water chemistry. If you have a lot of people over in your pool or have a party, you may want to shock your pool more frequently.

What happens if you put too much shock in a pool?

Although, if you overdo the shock treatment, you risk getting green hair from chlorine due to the excess chlorine oxidizing the copper in the water. You can execute a shock treatment with a few different types of pool shock, just be mindful of how much you're using.

Will Shock clear a cloudy pool?

Shock Your Pool

To eliminate any contaminants or chloramines in your cloudy pool water, add a high dose of chlorine by shocking your pool. If the cloudy water in your pool is due to a pool algae bloom, you'll have to double or triple shock depending on the type of algae you have.