Is Thompsons water Seal breathable?

Thompsons Water Seal, provides a clear long lasting waterproof seal, stops moisture, water or damp penetrating your exterior walls. Silicone micro emulsion is breathable and provides excellent protection for brick-work, aged concrete, render, slate, painting, terracotta and wood, exterior use only.

How long does Thompson's Water Seal take to cure?

Allow at least 48 hours to dry; however drying time will vary depending on the substrate, temperature, and humidity. Allow minimum of 30 days drying time before applying oil based paint over Thompson's® WaterSeal® Waterproofing Wood Sealer – Clear.

Can I use Thompson Water Seal indoors?

Yes. The water resistant formulation is suitable for both interior and exterior use.

How long does Thompson Water Seal take to dry before rain?

For deck stain, the deck surface and air temperature should be between 50 and 95 Fahrenheit for application and drying. The forecast should indicate no rain for at least 24 hours after application.

What's better than Thompson's Water Seal?

Thompson’s WaterSeal Review, Does It Work?!

Does Thompson water seal peel?

Thompson's WaterSeal has clearly not been a consumer favorite with deck stains or sealers. Mainly as it does not offer any UV protection and it grays in a few months. The Transparent and Semi-Transparent versions are prone to premature peeling and wearing after about 1 year.

Should I use Thompson water seal on pressure treated wood?

Some, like Thompson's^® WaterSeal^® Waterproofing Wood Protector, recommend waiting 30 days before application on new pressure treated lumber. Other products, like Thompson's^® WaterSeal^® Waterproofing Stain, can be applied immediately to new pressure treated lumber.

Can I use 2 coats of Thompson's water seal?

One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. With Thompson's^® WaterSeal^® Waterproofing Stains, you can clean your tools with soap and water.

Is Thompson Water Seal worth it?

Is Thompson's WaterSeal Any Good? Our experience with Thompson's WaterSeal Waterproofer Plus Clear Wood Protector was disappointing overall, and we would not recommend this product. Its inability to prevent UV graying is too harmful to your deck's wood.

What is the best way to apply Thompson's water seal?

The fastest way to apply is with a pump-up sprayer (using a coarse setting), but you can also apply with a brush or a roller. You should apply liberally. In the case of areas with heavy discoloration or dirt, apply a second coat, brush lightly with a broom and hose off.

Should I seal the inside of my shed?

By sealing your shed base from the inside, the water can't as easily get into the channels. This allows joints at the corners and drainage holes to give the moisture a way to escape, essentially keeping it away from the structure.

Is Thompson's water seal oil-based or water based?

Thompson's^® WaterSeal^® Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water. Each product has its own "feel" during application; however, each product provides protection from water damage and has a coating that resists mildew and UV damage.

How long does Thompson Water Seal last in can?

PVC primer and Thompson's Water Seal™, sealed tightly, can be kept indefinitely (no minimum temperature), as can concrete bonding additive if stored above freezing.

Can you use too much Thompson Water Seal?

Remove the excess product as soon as you notice it.

One of the common causes of water sealer not drying among first-time DIYers is applying the product in excess. As a result, they end up with the thick sticky residue of the sealant that remains lodged on the deck instead of drying as it should.

Is Thompson Water Seal toxic?

This product contains an in-can biocide, may be harmful if swallowed. There is no data on the product itself. The product should not be allowed to enter drains or water courses or be deposited were it can affect ground or surface waters.

Does Thompsons water seal dry?

DRYING TIME Thompson's Water Seal should be dry in 2 hours under normal conditions. Dry times depend on the texture & type of surface you're coating. Remove as much product as possible from equipment before cleaning. All equipment should be cleaned immediately after use with detergent and warm water.

Does Thompsons Water Seal smell?

Registered. I wouldnt use Thompson water seal, it has a strong smell that sticks around for along time!

Is Thompson water seal acrylic?

Thompsons WaterSeal Deck & House 100 Percent Acrylic Latex Waterproofing Solid Stain, Russet 16141 enhances the natural beauty of wood by adding exceptional fade resistant beautiful color that hides the wood grain while allowing wood texture to show. This formula is available in 67 rich tones.

What temperature do you apply Thompson's Water Seal?

Be sure that both surface and air temperatures are above 50°F during application and remain above 40°F for 48 hours after application. Do not apply product if rain is forecasted within 24 hours of application. Perform the splash test. Sprinkle water on various sections of surface to be sealed.

Is it better to stain or seal a deck?

Deck sealing will protect the wood from splitting, cracking, moisture, mildew, and rot while maintaining the color and grain of the wood. A stain will protect the wood and provides a more uniform tint or color to the wood to complement surrounding structures.

How do you clean brushes after using Thompson's Water Seal?

After waiting the recommended time, use a synthetic, stiff bristled brush to scrub the surface. Then use a garden hose or pressure washer to rinse away the residue.

What is the best sealant for pressure treated wood?

Do you need to seal cut ends of pressure treated wood?

IN-GROUND APPLICATION. Whilst treating or sealing any cut ends is important with any Treated Lumber product, maintaining a sealed end is most important when applicating Pressure Treated lumber in-ground, such as Fence Posts and Landscaping / Retaining Wall.

What happens if you don't stain pressure treated wood?

Pressure-treated wood is a porous material. Without stain, any type of paint or sealant, rainwater, dew or snow can easily penetrate the decking. The wood will then swell until it dries when it will shrink again.

Why is my deck sticky after sealing?

"A sticky or tacky deck is usually due to over-application or failing to wipe the excess stain from the surface of the wood. We recommend our Penofin Pro-Tech Cleaner Step 2. This is a product that comes in powder form. You mix 1 cup to a gallon of water, wet the wood and apply the solution to the wood surface.