Is EIFS more expensive than stucco?

EIFS is more costly than traditional stucco.

Which is better EIFS or stucco?

Synthetic EIFS stucco is slightly more energy-efficient than old-school hard-coat stucco, offering better insulation, though it's more complicated and expensive to install. Hard-coat stucco holds up better to water, making it a good choice for areas with plenty of moisture.

Is EIFS expensive?

EIFS is one of the most economical systems available, with an estimated material cost per square foot at $0.86 and installation cost of $5 to $6, which compares with the cost per square foot for brick at $1.25 with an installation cost of $8.50. EIFS also provides several other advantages over brick construction.

What is the problem with EIFS?

The problems with barrier EIFS cladding all stem from water intrusion. These problems include moisture accumulation in the wall cavity, subsequent wood damage and, in more advanced cases, mold growth and the infestation of pests such as carpenter ants or termites.

How many years does EIFS last?

A. Dryvit EIFS are designed to last for the typical design life of a building. The actual longevity on any specific building will depend mainly on the building maintenance program. Some EIFS facades date back 50-60 years.

Stucco Vs EIFS - What’s the difference?

Do people still use EIFS?

Yet today, EIFS are still around. About 100 million square feet of EIFS went on new and remodeled homes last year, rivaling any other siding material.

Can you pressure wash EIFS?

The best way to clean EIFS is to use high water volume coupled with low water pressure and non-abrasive cleaners. Do not use caustic chemicals or abrasive cleaning techniques, which will permanently damage the finish.

Does EIFS crack?

Some EIFS laminas crack sooner than others, but they all eventually crack. The cracks are due to hygric and thermal stresses, embrittlement due to aging, and building movement. The cracks in EIFS laminas are often found initially at reveals and at window openings.

Can you patch EIFS?

To fix deeper gouges, we cut out a small rectangle of the EIFS — no bigger than is needed to remove the damaged area — then fill it with a patch made from EPS foam.

How common is EIFS stucco?

Today, the EIFS market segment is less than 5 percent for residential construction.

How can you tell stucco from EIFS?

Go outside and knock on an outer “stucco” wall of your home. If it sounds hollow, there is a good chance you have EIFS. If it feels like you are knocking on a brick wall, it is more likely that you are knocking on traditional “hard-coat” stucco.

Is synthetic stucco the same as EIFS?

Synthetic stucco is commonly referred to as Exterior Insulating and Finish System (EIFS). Homes with this exterior finish are often strikingly beautiful, offer great flexibility in home design, and provide energy savings.

Can EIFS stucco be painted?

On a side note, EIFS can be painted just like traditional stucco. Depending on the characteristics and appearance wanted, our professional commercial paint contractors use either top-quality acrylic latex paints or elastomeric coating systems.

How do you tell if your house is EIFS?

The easiest way to identify synthetic stucco (EIFS) is by touching the material with your bare hand. When you touch the wall where the stucco is installed, it will feel like plastic. You can also knock gently on the wall. If it sounds hollow and thin, you have EIFS on your home.

What is the difference between Dryvit and EIFS?

Having a house with EIFS, also known as Dryvit, isn't the end of the world. EIFS isn't a disease; it's synthetic stucco. And even though your house may have been built using it, with knowledge and proper maintenance everything can be just fine. EIFS is an Exterior Insulation and Finish System.

What is the difference between stucco and Dryvit?

Dryvit stucco is actually the name of a stucco manufacturer, not an actual stucco system specifically. Dryvit is the name of the stucco company and they have different stucco systems including 3 coat stucco systems, EIFS systems, decorative systems and more.

How is EIFS installed?

EIFS installation

EIFS are typically attached to the outside face of exterior walls with an adhesive (cementitious or acrylic based) or mechanical fasteners. Adhesives are commonly used to attach EIFS to gypsum board, cement board, or concrete substrates.

Is EIFS a vapor barrier?

When you install EIFS on the exterior wall, it acts as a vapor barrier on the cold side of that wall. When fiberglass-batt insulation is then installed in the wall cavity, condensation occurs inside the wall at the (substrate) sheathing when a contrast in temperature exists from inside to outside.

Why should barrier wall EIFS be avoided?

MOISTURE ISSUES

The barrier in any EIF system is the basecoat and mesh layer. This layer will not allow the penetration of moisture and functions as the moisture-intrusion-preventing workhorse of the system.

How thick is EIFS system?

The total thickness of EIFS “Lamina” is generally 1/16” to 1/8” but can be thicker in areas of high-impact, by using high impact resistant mesh. Similar to stucco it is important to follow a proper design by a registered design professional or the EIFS manufacturer.

Should you paint EIFS?

Unlike wood, stucco and other siding materials, EIFS rarely need painting. Most EIFS systems are specifically formulated with 100% acrylic binder, which gives EIFS superior resistance to fading, chalking and yellowing. As a result, the systems tend to maintain their original appearance over time.

What is wrong with synthetic stucco?

Severe Synthetic Stucco Problems

Delamination, which is synthetic stucco detaching from your home's exterior. Rotting of wood beams and trim. Mold and mildew growth, both on interior walls and beneath on the home's base walls. Infestation of termites and other moisture seeking insects.

How do you maintain synthetic stucco?

Use gentle pressure and scrubbing to keep your synthetic stucco durable and resistant to wear. Regular cleaning with the proper technique can ensure your synthetic stucco finish looks its best. Fill a pump sprayer with 1 qt. chlorine bleach and 1 cup trisodium phosphate per gallon of warm water.