Is 18 inches deep enough for a fence post?

The general rule of thumb when setting a post is that the depth of the post's hole needs to be one-third to one-half of the actual above-ground height of the post. So, a six-foot-high finished post ideally needs to be buried three feet into the ground.

How deep should a 8 foot fence post be?

How Deep Should a Fence Post Be? For an average fence post, about 6 to 8 feet tall, prepare to dig a post hole about 2 feet deep. To install a fence post, you'll need a shovel or post digger, a 6-foot level, soil, and gravel or crushed stone.

How deep should a fence post go in the ground?

The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet). Add about 6 inches of QUIKRETE All-Purpose Gravel into the bottom of the hole. Then compact and level the gravel using a post or 2x4.

How deep should you bury a 12 foot post?

The general rule of thumb when setting a post is that the depth of the post's hole needs to be one-third to one-half of the actual above-ground height of the post. So, a six-foot-high finished post ideally needs to be buried three feet into the ground.

How deep should a 6ft fence post be?

The width of the post hole should be 3 times the width of diameter of the post. For example, if you are erecting a 6 foot high fence using 4 inch fence posts, the posts need to be 6 feet above the ground. 6 divided by 3 is 2, therefore the depth of the hole required is 2 feet.

How To Build A Fence: How Deep Should Fence Posts Be Set?

Is 3 feet deep enough for fence posts?

As a general rule of thumb one-third of your post should be underground, the other two-thirds above. Let's take a standard 6foot (72 inches) fence as an example. You will need a 9foot (108 Inches) post so that 3ft (35 inches) can be underground and 6ft can be above ground.

How many bags of quikrete do I need per fence post?

1 – 4 bags of concrete per fence post are typically what's needed. This depends on the type of soil, fence design, height, post size and bag weight. In general the depth of the post's hole needs to be 1/3 to 1/2 of the above ground height of the post.

How much concrete do I need for a 4x4 post?

Mix two 50lb bags of concrete with water in a mixing tub or 5-gallon bucket. Add concrete into the hole and around the 4” x 4”. Depending on your climate, let concrete set up for 24 - 48 hours.

Should I use concrete or cement for fence posts?

Concrete is the most secure material for setting fence posts, especially if you have sandy soil. Gravel may be okay with dense, clay-heavy soil, but in looser soil, concrete is the only thing that will truly keep your fence posts stuck in place.

How long does concrete take to set in a post hole?

The concrete sets up in 20 to 40 minutes, so you can quickly move on to the next stage of the project (a great convenience when setting fence posts) or backfill the hole to finish the job. Under normal curing conditions, you can apply heavy weight to the post (a basketball backboard, for example) after just 4 hours.

How long will a treated 4x4 post last in the ground?

A treated 4×4 will last 20 to 25 years in the ground if the conditions in the soil and climate are favorable. That number could increase to 40 to 75 years if you install the treated 4×4 in a cement ring rather than the soil. There are a few factors that influence how long the 4×4 can last in the ground.

How many bags of concrete do you need for a fence post?

Most fence post holes will need between 1 - 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post. Depth of the hole is one-third to half the above ground height of the fence post.

Do fence post need to be below the frost line?

All fence posts should be cemented in the ground below frost level. Check your local frost level and dig deeper by at least 6".

Is quikrete good for fence posts?

The best concrete mix for fence posts I've found is Quikrete Fast Setting Concrete Mix in a 50 lb bag. It's 4000 psi, easy to work with, sets up fast, and doesn't need to be mixed. Just pour it in the hole and soak with water.

Is it better to pour concrete wet or dry?

Dry the ground out even more by throwing an inch of sand onto the ground. Not only will this absorb the water, but it will make it an ideal surface to pour concrete on as the sand holds up much better in colder weather.

What happens if you add too much water to quikrete?

NOTE: the more water that is added to the mix the weaker it becomes; adding one extra quart of water per 80 lb bag can reduce the strength of the concrete by up to 40%.

Should pressure treated posts be set in concrete?

With pressure-treated posts, the rot will be slow. We have three ways to solve the rotten post problem. First, the posts should be set on top of a bed of coarse gravel 3 to 6 inches deep, so the base of the post is in contact with the gravel. Concrete should be poured around the post - no concrete under the post.

Should you concrete a wood fence post?

No, fence posts don't need to be set in concrete, and there are plenty of other ways to fix your posts if this feels a bit too permanent. If you are using wooden posts, concrete may actually be the worst option.

What lasts longer cedar or pressure treated wood?

When it comes to comparing treated wood vs. cedar, pressure-treated wood is the sturdier and more weather-proof of the two. It's highly resistant to insect attack and rot, and special versions rated for “ground contact” can be buried in soil and will continue to shrug off decay for decades.

Is quikrete the same as concrete?

Quikrete is concrete. They're both primarily sand, cement and aggregate stone. The only difference is that Quikrete has some additional ingredients and slight different ratios that make it set up faster. But it's still concrete.

How do I keep my post level while concrete dries?

You need to level it in two directions with a 4-foot level. After getting it straight in the first direction, hold one of the braces against the post and drive a single screw to connect the brace to the post. You can then level and brace the post in the other direction and begin filling the hole.

How long should you let fence post set in concrete?

Typically, you can apply some weight to the posts after 4 hours, but it's a good idea to wait at least 24 hours before resuming fence construction. Standard concrete mixes may take up to two hours to set and should cure for 24 to 48 hours before any forces are applied to the posts.