How often should you shock your well?

Homeowners with private wells should have their well water tested every 3 to 5 years for some contaminants, including bacteria.

Is shocking a well Necessary?

Shock chlorination is a method of disinfecting a water well. It is recommended when a water system is contaminated with bacteria. Contamination can occur when the well is installed, when repairs are made to the pump or plumbing, or when rainfall runoff enters the well.

How long does it take for water to clear after shocking a well?

It will usually take 4 to 8 hours to flush the well after a standard well chlorination. The water may become discolored during flushing because the chlorine may have loosened the hard water deposits in the plumbing. Caution: The chlorine must be completely flushed from plumbing system.

How long should I shock my well?

Pour it into the well without pumping. Allow chlorinated water to stand in the well and pipes for at least 8 hours (preferably 12 to 24 hours). Run water from outdoor faucets to waste (away from desirable vegetation) until the chlorine odor is slight or not detected at each faucet.

How much does it cost to shock your well?

In the United States, it costs between $60 and $100 to complete a shocking well. Depending on where you live, the cast will differ. If possible, you can reduce the expense using your own method. Gloves and a safe bucket are needed for chlorine use.

How to Disinfect Your Well

Should you put Clorox in your well?

You can disinfect your well with household chlorine bleach such as Clorox, Purex or a generic brand. The chlorine in the bleach kills bacteria. Note that it may take more than one chlorination for your well to return a satisfactory test.

What happens if you put too much bleach in well?

According to AskingLot, if you put too much bleach in your well, it can destroy the good bacteria found in the well, which can be a significant problem! The company also says that you should dilute the bleach with water so the pipes do not get ruined.

How often do you put bleach in your well?

Homeowners with private wells should have their well water tested every 3 to 5 years for some contaminants, including bacteria. If these tests turn up positive for bacteria, chlorinating the well may be a way to resolve the problem.

Will shocking a well get rid of coliform?

When done properly, shock chlorination will kill all the bacteria existing in a well. A recent Penn State study of wells contaminated by coliform bacteria found that shock chlorination and installation of a sanitary well cap successfully removed the bacteria for one year in 15 percent of the wells.

Does shocking a well help with iron?

With shock chlorination, the entire system (from the water-bearing formation, through the well bore and the distribution system) is exposed to water that has a concentration of chlorine strong enough to kill iron and sulfate-reducing bacteria.

Why does my well water turn brown when I add bleach?

The brown is the iron in the water that has oxidized as a result of the chlorination. Normally, the iron in water is in ion form and does not display itself until it combines with oxygen and forms common rust which turns the water reddish-brown.

How much chlorine do you use to shock a well?

Dug well (1 meter/3 foot diameter)

Add 1 litre (1 quart) of household bleach for every 1.5 metres (5 feet) of depth of water. If you don't know how high the water stands, use the well casing depth to estimate how much household bleach to use.

How do you shock a residential well?

Use ordinary liquid laundry bleach to shock chlorinate the water system. Determine how much bleach to use, then pour the bleach down the well and circulate it through the whole water distribution system. Wait 6-12 hours for the chlorine to work, then flush the chlorinated water from your well and pipes.

Will Shocking well get rid of sulfur smell?

1. Shock your well with chlorine bleach or hydrogen peroxide to get temporary relief from sulfur odors. Often keeps odors away for 1 – 2 months.

How common is coliform in well water?

Coliform bacteria are one of the most common water contamination problems in private water systems in Pennsylvania and throughout the United States. A 2006 survey of 450 private wells found coliform bacteria in approximately 35 percent and E. coli bacteria in about 15 percent of private wells.

How long can you leave bleach in a well?

Mix the bleach with the well water.

Then place the hose in the hole where you poured the bleach, allow the water to run back into the well for 15-20 minutes.

How do you flush sediment out of a well?

How do you maintain a well?

Keep hazardous chemicals, such as paint, fertilizer, pesticides and motor oil away from your well. Periodically check the well cover or well cap on top of the casing (well) to ensure it is in good repair. Always maintain proper separation between your well and buildings, waste systems, or chemical storage facilities.

What is a natural way to clean well water?

You can boil the well water for 5 minutes. With this, all the bacteria inside it will be eliminated. However, boiling will not be able to remove the solids and other materials inside the well water. The use of chlorine drops or iodine tablets can effectively kill the bacteria in the well water.

How do you make well water taste better?

You can help remove smells and taste by adding powdered activated carbon (GAC) to water or using granular activated carbon to make the water filter. Usually, powdered activated carbon (PAC) is better when the taste and odor aren't too strong or infrequent.

Why does my well water smell like sewer?

If your cold well water smells like sewage, it can be the result of several causes: Hydrogen sulfide from iron, sulfur or other types of bacteria naturally occurring in your well water. Contaminated pipes with layers of bio-film caused by various types of iron, sulfur, or other types of bacteria.

How many chlorine tablets should I put in my well?

Drop the proper number of pool chlorine tablets into the well. For a 10-foot well use 2 tsp. of a chlorine tablet, for a 20-foot well use 1 1/2 tbsp. of a chlorine tablet, for a 40-foot well use 3 tbsp.

How do I know how much water is in my well?

First, subtract the depth to water from the overall depth of the well. For example, if our well was ten feet deep and it was a foot to water, we'd have nine feet of water. Next, use the following equation: pi (or 3.15 if you're not using a calculator) times the square of your radius times the height of your well.

Is it OK to have coliform in well water?

Most coliform bacteria are not harmful. However, some can make you sick. A person that has been exposed to these bacteria may have an upset stomach, vomiting, fever, or diarrhea. Children and the elderly are more at risk from these bacteria.