How often should you redo polymeric sand?

If you chose polymeric sand, even if exposed to the same circumstances as regular sand, it may last up to ten years (or more). Note that to increase durability, you can apply a sealer over pavers in both cases (polymeric and regular sand).

When can I reapply polymeric sand?

First, you run the danger of disturbing your base/shifting your pavers. Secondly, you will have to wait a day while the surface dries before you can reapply your new sand. Remember polymeric sand and moisture don't mix until after it's in the joints!

Do I have to remove old polymeric sand?

But unlike normal sand, the compound hardens very quickly when you expose it to moisture or water. Thus, you must remove polymeric sand from pavers' surface before you finish your project. Still, the polymeric sand usage in paving projects is probably one of the best choices when it comes to sand types for joints.

Can I put new polymeric sand over old polymeric sand?

CAN I USE POLYMERIC JOINTING SAND? Yes. If you are tired of sand erosion, weeds and ants on your pavers, Techniseal Polymeric Jointing Sand can be used to replace old sand in your joints. Simply remove the old sand completely and apply Techniseal Jointing Sand.

Can you add another layer of polymeric sand?

It is not ideal to add a thin layer of polymeric sand on top of what's already there for many reasons: the original sand can be old, of unknown condition, and/or dirty. The best approach would be to remove at least 1" of the jointing material and follow the steps for a new polymeric sand installation.

Problems with Polymeric Sand | How We Solved This Failure

How long does polymeric sand last?

Polymeric sand can last up to 10 years before replacement is necessary. However, certain manufacturers claim some products can last up to 15 years.

Why does polymeric sand fail?

Polymeric sand cures by drying. And in order to fully set, it needs to dry out completely. If your polymeric sand didn't harden up, it's pretty much guaranteed there's a moisture issue. If the joints remain wet after the installation, they will remain soft until they dry.

How often should you apply polymeric sand to pavers?

If you chose polymeric sand, even if exposed to the same circumstances as regular sand, it may last up to ten years (or more). Note that to increase durability, you can apply a sealer over pavers in both cases (polymeric and regular sand).

Can you pressure wash polymeric sand?

You can't pressure wash and apply polymeric sand on the same day. I should warn you that getting the stain off is a huge problem so it's best to take the time to avoid it in the first place.

Does polymeric sand need to be sealed?

Without any kind of sealer, the sand in your joints will blow and wash away. Fortunately, if you use one of Seal \'n Lock's paver sealers, you won't have to worry one bit about purchasing or installing polymer sand.

Is it hard to remove polymeric sand?

Knowing how to remove polymeric sand from pavers is not difficult, just time consuming and tedious. Warm to hot water actually reactivates the polymers within the sand and allows you to scrub or wash away the sand that is stuck to the surface of the pavers.

How do you refresh paver sand?

To replace sand that has been washed out, simply pour joint sand over the pavers. Next, sweep it into and across the joints using a stiff push broom. Keep the depth of the sand at ¼ inch from the surface of the paver. Afterwards, you can sweep the excess joint sand between pavers and store it again for future use.

How do you clean pavers without removing polymeric sand?

Wet The Patio With Water

After it's wet, then add some dish soap or a degreaser to a bucket of water. Using a brush that's stiff, pour some water and soap on the pavers and give it all a scrub. Keep it gentle, and don't go overboard on the scrubbing, so you don't damage any of the surfaces.

Can you over water polymeric sand?

When watering in the Poly Sand, remember Goldilocks - "This is just right." Don't use too much or too little water. The amount of water you use is a critical element to an installation. Using too much water can cause the joint to over-saturate and result in polymer washout, mushy sand, and a weak bond.

How big a gap can polymeric sand fill?

How Big a Gap Can Polymeric Sand Fill? Polymeric sand works best to fill gaps between 1/4 inch and 1.5 inches wide. Wider joints will require more time to harden.

What if it rains on polymeric sand?

Installing polymeric sand on a damp or wet surface could cause the sand and polymers to stick to the surface and become difficult to remove. After installation, a hard rain on polymeric sand that has not fully set up could result in polymeric sand all over the top of the pavers.

How do you remove the haze from polymeric sand?

Poly Sand Haze Tips

If poly sand haze has transpired on the surface, it must be cleaned with an acid-based cleaner. Sometimes vinegar can be used unless the poly sand haze is severe. Many times, homeowners and even contractors are unaware of poly sand haze.

How permanent is polymeric sand?

Polymeric sand relies on a chemical reaction to harden it into the joints between your paving stones. Once it hardens, it is permanent. Unfortunately this also is true for the polyhaze that often appears on the surface of your paving stones.

Does polymeric sand crack?

UNDER-WATERING causes the polymeric sand to simply form a "crust" on the top. If you only have a crust, you don't have a proper bond in the joints. Eventually, the crust will break away, eroding the joint. It also causes cracks and gaps, because the sand hasn't fully bonded the entire depth of the joint.

How do I stop weeds from growing between pavers?

Weeds want to inhabit a cool damp environment; proper drainage will help avoid weed growth. Regular Sweeping. Brushing your paving stones will prevent seedlings from settling, and will disrupt new weeds from fully establishing a place between your pavers.

How long does it take for polymeric sand to harden?

A minimum of 24 hours drying time is required prior to allowing significant foot traffic and 48 hours for vehicular traffic on the paver surface. Polymeric sands are designed to soften and re-heal.

Can I power wash my paver patio?

Pressure washing concrete pavers, especially newer ones, can easily damage the surface finish and we strongly suggest not pressure washing unless you are highly experienced and have the right equipment to pressure wash pavers. In most cases, to get pavers clean with a pressure washer it requires using a jet style tip.

Is there something better than polymeric sand?

When looking for alternatives to polymeric sand, you will also want to find high quality materials. There are other products, such as EnviroSAND, EnviroSTONE and EnviroPATH on the market that are able to stop water erosion from occurring.