How much does PolyLevel cost?

How Much Does PolyLevel Cost? PolyLevel costs about $15 per square foot or around 30% to 40% more than standard mudjacking. PolyLevel is a patented, high-density polyurethane foam used for heavy-duty concrete stabilization projects like home foundation and driveway work. This polyfoam cures in as few as 30 minutes.

How long does Poly leveling last?

How long will it last (under normal conditions)? Reports on mudjacking vary, so a comprehensive range can be considered 5-10 years, depending on conditions. This is because, at the end of the day, the slurry being used to lift the slab is still partly made of dirt (“mud”).

How much does foam injection cost?

Here is a general pricing guide to provide an idea of what you can expect to pay for polyurethane foam injection: The cost of an average residential polyurethane foam injection is between $2,400 and $3,600. For smaller residences, the average cost of polyurethane foam injection is between $10 and $25 per square foot.

How much does it cost to level concrete with foam?

When you include the pounds of foam required, the size of the project, additional voids, weather and access to the work site, the average cost of lifting and leveling your concrete is between $7.00 and $12.00 per pound of polyurethane foam.

What is the cost of Polyjacking?

Polyjacking costs start at around $900 for a basic job up to $7,500 for extensive needs. We mentioned that both of these repair types are more cost-effective than a full replacement of concrete surfaces.

HouseSmarts "PolyLevel: Concrete Leveling" Episode 167

How good is Polylevel?

Polylevel is waterproof, so it will never wash out, and it won't degrade over time due to temperature extremes. Best of all, Polylevel cures quickly, allowing your concrete to be used normally the same day.

Which is better Mudjacking vs foam?

Foam injections cure in 15 minutes compared to a full day for mudjacking. It's less invasive because it requires smaller and fewer drilling holes. It's stronger, doesn't retain moisture or pollute the environment, and can reach areas that are inaccessible to mudjacking equipment.

What is PolyLevel?

PolyLevel is a patented product that we inject beneath concrete slabs: driveways, sidewalks, pool decks, and porches. PolyLevel is a high-density polyurethane that can lift slabs, correct unevenness, remove tripping hazards and concrete eyesores.

Can I raise concrete myself?

Lifting a sunken slab may be necessary to level the surface. Hiring a professional service to lift, or jack up, the slab can be costly. You can avoid this expense if you do it yourself with the help of a jacking pump, which can raise the concrete slab to the needed level.

Is polyurethane foam expensive?

Polyurethane Foam (also known as poly-foam) is the least expensive and lowest quality foam used in mattresses and mattress toppers.

Is RetroFoam worth the money?

RetroFoam isn't one of the cheap ways to insulate a home. As a matter of fact, RetroFoam insulation is one of the more expensive options. Injection foam insulation is more expensive than fiberglass or cellulose because it is a superior product that creates an air seal that traditional materials can't.

How much does polyurethane foam cost?

Traditional Polyurethane Spray Foam

Expect to pay $0.44 to $1.50 per board foot for professional installation of polyurethane foam insulation.

How long does concrete foam jacking last?

Unlike short term options like mudjacking, PolyLevel is a solution that will last. A study done in 2006 by Argonne National Laboratory found that the longevity of rigid PolyLevel foam is more than 1000 years.

How do you lift sagging concrete?

Mud jacking can lift a settled concrete slab by pumping a grout through the concrete and pushing it up from below. The process is sometimes called “slab jacking” or “pressure grouting”. 1 to 1 5/8th inch diameter holes are drilled through the sunken concrete block/slab at strategic locations to maximize lift.

Is PolyLEVEL toxic?

Not only is Polylevel the most reliable solution for sinking concrete, but it's a solution you can feel good about knowing that it's not harmful to the environment.

Do It Yourself lift concrete slab?

How much does concrete crack injection cost?

The cost is usually only a few hundred dollars depending on the size and length of the crack. The national average cost for crack injection is $4,500, while most projects range from $2,300 to $6,700. Minor cracks may only cost a few hundred dollars, but the larger the crack, the more expensive the repair.

What kind of foam is used to lift concrete?

The form used to lift and level concrete is made of polyurethane. The way that it is mixed and the chemical make up allow it to expand in space is that it is injected into. It's a very non-invasive process.

What is PU foam spray?

Spray Polyurethane Foam is a polyurethane (PU) based, single component, very qualified heat and sound insulation product that can be applied by being sprayed on surfaces through its special application device. The propellant in the can sprays the chemical component to surfaces through application gun.

How long does PU foam last?

The durability of polyurethane will depend on the application and the use given to the product. For example, in normal wear conditions you can expect a shelf life of over 50 years in building insulation, for more than 25 years in fridges, and more than 20 years in motor car bumpers.

Is great stuff polyurethane foam?

Great Stuff Pro™ Gaps & Cracks Polyurethane Foam Sealant is a minimal-expanding, single-component polyurethane foam sealant for general purpose building envelope air sealing and retrofit applications. It has been tested and approved as an alternative fireblock material.

Does foam hold concrete?

The foam will fill up the parts of the concrete that are uneven and will raise it to the proper height. After the Geolift has done its' magical work, the last thing left to do is patching up the holes. Patch up the holes with concrete, and your new driveway (or sidewalk, or walkway) will look good as new.