How many coats of Thompson Water Seal do I need?

One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. With Thompson's^® WaterSeal^® Waterproofing Stains, you can clean your tools with soap and water.

Does Thompsons water seal need two coats?

Thompson's WaterSeal products typically need only one application, but you can apply a second coat of stain to darken the wood, if desired. However, you must wait for the first coat to dry (typically about 2 hours) and apply the second coat within 4 hours of applying the first coat.

Can you use too much Thompson Water Seal?

Remove the excess product as soon as you notice it.

One of the common causes of water sealer not drying among first-time DIYers is applying the product in excess. As a result, they end up with the thick sticky residue of the sealant that remains lodged on the deck instead of drying as it should.

How many coats of Thompson Water Seal should I put on?

Apply 2 coats using brush,roller or sprayer. note: Use at full strength.do not dilute. The second coat should be applied when the first coat has soaked in the surface. For best results do not leave the first coat to dry for more than 1 hour before applying the second coat.

How many years does Thompson Water Seal last?

Water Seal can only be used on bare and uncoated brick, stone or concrete. How long will Water Seal last? If applied correctly, Water Seal will last up to 4 years. This is dependent on conditions such as orientation of the wall and local climate.

Thompson’s WaterSeal Review, Does It Work?!

What's better than Thompson's Water Seal?

Does Thompson Water Seal peel?

Thompson's WaterSeal has clearly not been a consumer favorite with deck stains or sealers. Mainly as it does not offer any UV protection and it grays in a few months. The Transparent and Semi-Transparent versions are prone to premature peeling and wearing after about 1 year.

Should I put two coats of sealer on my deck?

Overly thick sealant is prone to peeling and chipping, so avoid oversaturating the surface by applying only one coat of sealant at a time. In most cases all you'll need is one coat, but if you decide to apply a second coat, wait at least 24 hours.

How long does Thompson Water Seal take to dry before rain?

Coverage will vary depending on the texture and porosity of the surface to being treated. DRYING TIME Thompson's Water Seal should be dry in 2 hours under normal conditions.

What is the best way to apply Thompson Water Seal?

The fastest way to apply is with a pump-up sprayer (using a coarse setting), but you can also apply with a brush or a roller. You should apply liberally. In the case of areas with heavy discoloration or dirt, apply a second coat, brush lightly with a broom and hose off.

Why is my deck sticky after sealing?

"A sticky or tacky deck is usually due to over-application or failing to wipe the excess stain from the surface of the wood. We recommend our Penofin Pro-Tech Cleaner Step 2. This is a product that comes in powder form. You mix 1 cup to a gallon of water, wet the wood and apply the solution to the wood surface.

Should I pressure wash my deck before sealing?

Pressure washing is the best way to prepare your deck for sealing. After you've pressure washed your deck, you'll need to wait for it to completely dry. Sometimes, this can take as long as 48-hours.

Can Thompson water Seal go over stain?

Yes, you can put Thompson water sealer over stained wood whether the stain is water or oil-based. But surface preparation is key. If the stain has completely dried and cured it's fine to apply sealer, but if there is still some moisture, applying the water seal over the stain might cause problems.

Should I use Thompson water Seal on pressure treated wood?

Some, like Thompson's^® WaterSeal^® Waterproofing Wood Protector, recommend waiting 30 days before application on new pressure treated lumber. Other products, like Thompson's^® WaterSeal^® Waterproofing Stain, can be applied immediately to new pressure treated lumber.

Is Thompson water seal worth it?

Is Thompson's WaterSeal Any Good? Our experience with Thompson's WaterSeal Waterproofer Plus Clear Wood Protector was disappointing overall, and we would not recommend this product. Its inability to prevent UV graying is too harmful to your deck's wood.

How long after applying Thompson water seal can you walk on it?

Now that you've applied Thompson's Water Seal following the instructions above, to your entire surface, you can walk away and let it dry for 24 hours. That's all the time you need to let Thompson's Water Seal work to protect your outdoor surfaces from water damage.

Is it better to stain or seal a deck?

Deck sealing will protect the wood from splitting, cracking, moisture, mildew, and rot while maintaining the color and grain of the wood. A stain will protect the wood and provides a more uniform tint or color to the wood to complement surrounding structures.

Can I apply a second coat of water based stain a week later?

Can I Apply a Second Coat of Stain a Week Later? No, applying a second coat of stain a week later is a bad idea. If you apply another coat of wood stain after a week, it will not adhere to the wood properly. As a result, any finish you use on top will experience adhesion problems and peel off.

Is 1 coat of stain enough?

Two coats are generally better than one

If the deck has been properly cleaned, it should absorb the first of stain well in to the wood. By applying a second, light coat of material, you will fill up the cell structure of the wood (kind of like topping off the tank) and the project will last longer.

How many coats does decking need?

Make life easy with a good decking oil

Just clean the surface thoroughly using a good quality decking cleaner, which will get rid of the dirt, then re-oil it. 2-3 coats should do the trick.

What happens if you put too much stain on a deck?

You'll know if you've over-applied your deck stain because there will be sticky patches or puddles that just aren't drying—the wood has absorbed all it can so the remaining stain has nowhere to go.”

Can you put Thompson's Water Seal on wet wood?

Thompson's^® WaterSeal^® Waterproofing Stains can be applied to damp wood, so you only have to wait about two hours to begin applying stain. Some of our other products require that the wood dry for 48 hours before applying a deck coating.

Is Thompson's Water Seal oil or water based?

Thompson's^® WaterSeal^® Penetrating Timber Oil is an oil-based product that provides protection by penetrating into wood pores and sealing out water infiltration. Thompson's^® WaterSeal^® Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water.

What is the longest lasting deck sealer?

Q. What is the longest-lasting deck sealer? An oil-based deck sealer, such as Varathane Ultimate Spar Urethane Oil Based, will protect a deck for up to 5 years.