How many bags of Postcrete do you need per post?

you will need minimum 1 bag per post. I usually use one and a half per post but I am using 25kg bags. often poscrete is in 20kg bags so 2 per post is more likely.

Is 1 bag of Postcrete enough for one post?

The amount of Postcrete required will depend on the size of hole and post. For example: 1 bag = square post 10 cm (4”) with a hole 20 cm (8”) wide x 75 cm (30”) deep. Please refer to Product Datasheet for more details. Postcrete may not be used for general concreting, screeds, mortar, grout or render.

How many bags of Postcrete do you need for one post?

The exact amount of Post Mix Concrete needed will vary depending on the width and depth of the hole, but as a general rule you'll need about one and a third bags for a standard fence post.

Is 2 feet deep enough for fence posts?

The minimum depth that you should dig your fence post holes for panel sections is 2 feet. A general formula is to dig the holes one-third to one-half of the post's aboveground height. The deeper you dig the holes, the more stability your fence has, but you must also purchase longer posts.

How many bags of concrete do you need for a fence post?

Most fence post holes will need between 1 - 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post. Depth of the hole is one-third to half the above ground height of the fence post.

HOW TO USE POSTCRETE | WOODEN POST INSTALLATION | DECKING DIY

How deep should a 6-foot post be in the ground?

The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet). Add about 6 inches of QUIKRETE All-Purpose Gravel into the bottom of the hole. Then compact and level the gravel using a post or 2x4.

How deep should a 3 foot fence post be?

The general rule of thumb when setting a post is that the depth of the post's hole needs to be one-third to one-half of the actual above-ground height of the post. So, a six-foot-high finished post ideally needs to be buried three feet into the ground.

How much concrete do I need for post?

A: Finding the right amount of concrete depends on the size of the hole and the size of the post. The diameter of the hole should equal about three times the diameter of the post and the depth of the hole should be about ⅓ to ½ the total length of the pole.

How big of a hole do you need for a 4x4 post?

The diameter of your post hole should be three times the diameter of your post. So, if you're planning on using a four-inch round or 4x4-inch square post, your post hole will need to be 12 inches in diameter. For a six-foot-high fence post, we would need a hole that's 36 inches deep and 12 inches in diameter.

Can I use Postcrete instead of concrete?

What is Postcrete used for? Postcrete is ideal for fixing decking posts, rotary washing lines and small/medium sized gate posts for gates less than a metre in width. Postcrete should not be used for general concreting, screeds, mortar, grout or render.

How deep should a concrete fence post be?

Dig your hole to the correct depth, allowing for the height of the fence panel and the gravel board. As a rough guide the hole should be a minimum 1/3 the height of the fence, so a 6 foot fence would need an 8 foot post in a 2 foot deep hole. Similarly, the hole should be three times the diameter of the post.

How much water do you add to a bag of Postcrete?

Fill hole with water to a third of the depth. 3. Pour in POSTCRETE evenly around post until no standing water is visible (powder completely covers water surface).

How much post goes in the ground?

As a general rule of thumb, you'll need to place at least 1/3 the height of the post in the ground. For example, a 6-foot tall fence will need at least 2 feet of post in the ground.

How long does it take for Postcrete to fully set?

How long does it take for Postcrete to set? After adding water to the mix, Postcrete usually sets in 5-10 minutes, with the solution beginning to stiffen within 1-2 minutes.

How many 20kg bags of ready mix concrete do I need?

How many bags of concrete per m2. Generally, there are 11 bags of 20kg premixed concrete per m2. 1 square metre of concrete at 100mm deep weighs 220kg, so, number of bags of 20kg of concrete per m2 = 220 ÷ 20 = 11 bags. Thus, you will need 11 bags of 20kg concrete per square meter.

How deep should a 7 foot fence post be?

How Deep Should a Fence Post Be? For an average fence post, about 6 to 8 feet tall, prepare to dig a post hole about 2 feet deep. To install a fence post, you'll need a shovel or post digger, a 6-foot level, soil, and gravel or crushed stone.

How far apart should fence posts be?

Most fence posts can be spaced 8 to 12 feet apart. While this is a general criteria, it doesn't cover all scenarios. For instance, high tensile fence can have larger spacing, requiring line posts every 15 to 20 feet for field fence styles, and as much as 20-30 feet for high tensile barbed and smooth wire.

How do you keep fence posts from rotting in concrete?

Fill the first three inches up with gravel so the end of the post doesn't come into contact with the dirt. Gravel allows water to drain quickly away from the post and into the soil. Be sure to place the post in the center of the hole. Finally, fill the entire hole up with cement to the top.

How much gravel goes in the bottom of a post hole?

How much gravel do I put in the hole? You should put approximately 2" to 4" of gravel in the bottom of the hole making sure that the Post stands 6' 4" tall from the ground to the top of the post.

How long does concrete take to set in a post hole?

The concrete sets up in 20 to 40 minutes, so you can quickly move on to the next stage of the project (a great convenience when setting fence posts) or backfill the hole to finish the job. Under normal curing conditions, you can apply heavy weight to the post (a basketball backboard, for example) after just 4 hours.

What size post do you use for an 8 foot fence?

A common rule of thumb, is to dig the hole 3 times as large as the post, and to a depth of 1/3-1/2 of the post height above ground. so for a 8' high fence, using 4x4 posts. dig the holes 12" in diameter, to a depth of 2 1/2 - 4'. Of course, that's assuming you're setting the posts in concrete.