How do you treat a newly filled pool?

Add a clarifier to the water. The clarifier will help the filter to remove the very tiny particles that enter the pool in the filling process or that may remain following construction and installation. 5. Start the pump and filtration equipment and allow the water to circulate for 24 hours, if practical.

How do I treat my pool after first filling?

Run filter pump while adding chemicals to circulate. Re-test the pool water after 8 hours of filter run time. Add chlorine shock when the sun is not directly overhead. Add algaecides last, after chlorine level drops below 3 ppm.

What chemicals do I need to add to a freshly filled above ground pool?

Once the pool is opened and the floor and walls have been brushed the first chemical you should add is chlorine to shock it. It's recommended you add a gallon of liquid chlorine or pound of granular chlorine for every 5,000 gallons of water in the pool. You can also add more chlorine at the end of the opening process.

How do you treat water in a new pool?

What chemicals should I balance first in my pool?

Total Alkalinity (TA) is the first thing you should balance in your pool water. TA refers to the amount of alkaline material in the water. And since alkaline is a pH stabilizer, the number of alkaline substances in water will affect the pH balance. The ideal Total Alkalinity range for pool water is 80 – 120 ppm.

First Time Pool Owner: "Do's

How soon after filling a pool Can you swim?

Chlorine/non-chlorine chemicals – When adding chlorine or non-chlorine chemicals to “shock” your pool after a fill-up, wait about 24 hours or until levels are approximately 5 ppm. If you'll only be adding liquid chlorine, it's generally safe to swim after about 4 hours or until levels are 5 ppm or lower.

How much chlorine do I add to my pool for the first time?

If you're adding chlorine for the first time, add the amount of product required to achieve a free available chlorine level of 2 to 3 ppm. The instructions will let you know how much to use to raise levels by 1 ppm per 10,000 gallons (38,000 L) of water.

How do I start my above ground pool for the first time?

Do I add chlorine or stabilizer first?

Open your pool under normal procedures, and let the filter run with its normal amount of chemicals. When all the other chemicals, such as chlorine. pH and alkalinity, are balanced, add the chlorine stabilizer. Add the stabilizer only after the filter has been backwashed to ensure it is cycled through a clean filter.

How long can water sit in pool without chlorine?

If you are not adding chlorine to kill bacteria, drain the pool every other day. Stagnant water without chlorine can become unhealthy water in as little as 24-48 hours.

Is liquid chlorine better than shock?

Liquid chlorine is generally less costly than granular shock and comes in refillable containers, where granular shock does not. Liquid chlorine does not need to dissolve in your water as it is already in liquid form. In addition, liquid chlorine is non-scaling and leaves no residue.

Do I add chlorine everyday?

Chlorine sanitizer should not be put in your hot tub every day. Instead, it should be added 2-3 times per week depending on the frequency the tub gets used. Then about ¼ cup of chlorine shock should be added every 7-10 days. The amount of sanitizer to add depends on where the chlorine levels read on a test strip.

How do you start a new pool?

Why is my pool green after filling?

Your first instinct when you fill your pool with new water, is to shock it. But that shock then oxidizes the metals, that chemical reaction then causes the green hue in your water. This is common with refills that used well water or even water that hasn't been shocked but instead contains a high level of metals.

Do I use shock or algaecide first?

While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.

Do you adjust pH or alkalinity first?

Check Total Alkalinity (TA) first, then adjust for proper pH range. Proper TA will buffer pH, that is, it will help to prevent pH fluctuations. Use fresh, high quality test strips. Excessively high bromine or chlorine levels can result in false pH and TA readings.

Can I add stabilizer and chlorine at the same time?

Yes! Just make sure that you wait at least 20 minutes after adding chlorine stabilizer (and that it's completely dissolved into the water) before you go swimming. The same rule applies to all other swimming pool water chemicals including adding alkalinity increaser, chlorine, algaecide, and more.

Is shock the same as chlorine?

Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.

How many bags of shock do I need to open my pool?

You will need to quadruple shock your pool by added 4 pounds of shock to every 10,000 gallons of water. This can be expensive if you have a large swimming pool.

How long do I wait between adding pool chemicals?

Wait times for adding pool chemicals

The wait times between adding pool chemicals is usually around 10 minutes each, as that is also sufficient time for the chemicals to mix in the water. Users also under normal conditions can swim roughly 10 minutes after adding chemicals.

Can you use bleach instead of chlorine in a pool?

Short answer: yes. Longer answer: it depends on the formulation. The label on every bleach bottle should tell you the ratio of sodium hypochlorite (and available chlorine) in the bottle to everything else. A higher percentage is generally better, as you'll need to use less bleach to treat your pool.

Is Shocking a pool the same as adding chlorine?

SKIMMER NOTES: No. Chlorine and shock are not the same thing. Shock has a more intense chemical strength than the traditional chlorine sanitizers, and it also differs in how you should apply it to your swimming pool.

What is stabilizer for a pool?

Pool stabilizer is also sometimes called pool conditioner, chlorine stabilizer, or cyanuric acid (CYA). Its purpose is to stabilize the chlorine in your pool water, so the sanitizer lasts longer. This will ultimately help keep your water clean for a longer period of time.