How do you override a motion sensor switch?

Yes, most sensors will have the ability to override the sensor function altogether and operate the light manually, as necessary. This is done by turning the light switch OFF – ON – OFF – ON in quick succession. The light will then remain ON and will not go OFF until you manually turn it OFF at the switch.

Can you override a motion sensor light switch?

One of the quick tricks you can try is to quickly turn the motion sensor ON, OFF, ON to override the motion detection and make the light stay on. To go back to motion detection mode, turn the motion sensor switch off and wait for about 10 seconds, and then turn it on again.

Can a motion sensor be bypassed?

Many motion detectors can be bypassed with little effort. With an additional light switch, the connected outdoor light can then be switched to permanent light. The following sections should be carefully read before installing the light switch.

Can you disable a motion sensor light switch?

Most manufacturers make it a fairly easy process to disable this main feature of the lights. A switch on the fixture should read "on time," usually found directly under the motion sensor. Set it to any position, aside from the test position, and flip off the switch that the light is connected to.

How do you block motion sensors?

A quick solution that customers have said works well is to use black electrical tape to cover part of the sensor. Start by covering the edge of the sensor on the side you want to keep out of the detection area and use small pieces of tape to block it out.

Lighting Sensor Wiring with Override Facility

How do I make my indoor motion sensor light stay on?

Another Method To Keep Motion Sensor Light Stay ON

Place your hands in front of the lights to turn on then, wait for it to shut off. Then place a black tape over the sensor so it can no longer detect movement. Flip the switch off and on; this double flipping will allow the light to remain on.

Can you bypass motion sensor on outdoor light?

Yes, most sensors will have the ability to override the sensor function altogether and operate the light manually, as necessary. This is done by turning the light switch OFF – ON – OFF – ON in quick succession. The light will then remain ON and will not go OFF until you manually turn it OFF at the switch.

How do I bypass dusk to dawn sensor?

To disable the dusk-to-dawn sensor (D), you will need to install the sensor cap (CC) over the dusk-to-dawn sensor (D) (Fig. 2). This will prevent the dusk-to-dawn sensor (D) from controlling the ON/OFF function, and should allow you to control the fixture (A) with the wall switch. 1.

Can a motion sensor light be controlled by a switch?

If you use a motion sensor, this can act as a switch, controlling when the light goes on and off. However, there might be times when you'd like to stop the light from responding to the motion. If you want to stop the light from switching on every time anybody walks past, you can use a switch to stop it from working.

Can you bypass the sensors on a garage door?

Since most photo eye sensors are placed at that two-inch height, most people know you can simply step high above the infrared light to bypass the system. The garage door will continue to close if your steps avoid the photo eye sensor. Disconnecting the garage door opener from the garage door will bypass the sensors.

How do I reset my motion light stays on all the time?

Reset your Motion Detector – To reset your motion light, unplug it from its power source for a full 10 seconds. Plug it back in and allow it to come back on. This should reset your light and turn off the auto-on function.

What is a photocell resistor?

A photocell is a resistor that changes resistance depending on the amount of light incident on it. A photocell operates on semiconductor photoconductivity: the energy of photons hitting the semiconductor frees electrons to flow, decreasing the resistance.

What is a photocell shorting cap?

The shorting cap provides a closed circuit when a photo control is not installed, keeping lights continually on for safety. An open cap disconnects service when lighting is no longer needed.

Can motion lights be set to stay on?

Place a piece of electrical tape over the motion sensor to be certain that you correctly turn the light to the right setting to stay on without responding to movement.

Why does my sensor light not turn off?

If your outdoor security light won't turn off, it's most likely because of one of these problems: The sensitivity settings are too high. The duration settings are too high. It's stuck in auto mode.

How do I turn off my PIR motion sensor?

The only way to turn off the override function is to turn the switch off and wait for 30 seconds to 1 minute before you turn it on again. This should reset the sensor so that it works on motion detection again.

How do you cheat a garage door sensor?

So, all you need to do is hold the wall button down ( do not press and release). You must hold the wall button all the way down until the garage door hits the floor then release. If you let go of the button before the door hits the ground the sensors will kick back in to action and the door will reverse.