How do you open a safety clasp?

You can use your fingernail to flip it open. Grasp the flap with your fingers to pull the fold-over safety clasp open. Some fold-over clasps have a button on the top, located on the flat side of the clasp. When you push the button, this releases and opens the flap, allowing you to remove the bracelet.

How do you open a clasp lock?

To open it, push down on the lever with your thumb and the bottom section of the “claw” will swing inward. Releasing the lever closes the clasp. You can buy lobster clasps in a range of sizes and styles, including a version that allows the clasp portion to rotate 360 degrees without disturbing the jewelry at all.

How does a snap clasp work?

This hinged clasp folds shut, closing securely and locking with a quiet ''snap. '' With this secure closure, snap lock clasps are ideal for bracelets or anklets. Springring Clasps are used with a jump ring or chain tab to make a complete clasp. Pull the trigger to open.

What is a safety clasp?

Jewelry safety clasps are in the category of jewelry findings. You'll find safeties in bracelets, watches, necklaces, and pins and they are used to provide extra security to the closure. Often they are used to supplement a main clasp and other times they are used to protect the point of a pin.

How do you open a slider bracelet?

Both of the Sliding Bracelet's barrel clasps can be opened and removed. Simply push down on the opener of the barrel clasp and the tiny spring inside the barrel clasp will release the Sliding Bracelet chain. As you push down on the barrel clasp you will hear a little 'click' sound of the bracelet chain releasing.

How to UNCLASP a Box lock/ Safety lock...

How does a push clasp work?

Push or Clip Clasps

Operating in much the same way as a tiny climbing carabiner, these clasps have a one-way hinged portion. You can open it by pushing against it from the outside with your fingernail or the jump ring on the other end of your necklace or bracelet. This hinged area doesn't open from the inside.

How does a barrel clasp work?

Barrel clasps are also called torpedo clasps. These work via a threading mechanism, where you have to twist the clasp to open and close it. Usually, when the clasp is twisted close, it resembles a barrel, hence the name. Barrel clasps aren't ideal for bracelets because it's difficult to do up with one hand.

How do you open a Gorjana clasp?

How do safety chains work?

Safety chains are a recommended addition to your Pandora bracelet. With a Safety Chain on your bracelet the two ends of the bracelet are held more closely together. This makes putting on and taking off your bracelet easier, and helps in the unlikely event that your clasp opens unexpectedly.

How do you use a S hook clasp?

Open up the curve of the S-hook on the jumpring side to put the necklace or bracelet on and off. Some S-hook clasps have two jumprings, one on each half of the "S." Use the jumprings to end each end of your design. Then open and close the S-hook accordingly to take off and put on your necklace or bracelet.

How do you open a clasp that won't open?

Use the knife with your dominate hand. Insert the tip of the knife into the side of the clasp and gently twist the knife to increase the distance between the top and bottom of the clasp. Open and close the clasp after each twist to check if it is working properly. Go slowly and gently with this repair.

What is a fold over clasp?

Fold over clasps and box clasps are very popular and are easy to use. Many vintage jewelry designs have fold over and box clasps. Fold over clasps are typically brass and are attached to a necklace or bracelet by crimping the end to a jump ring.

How do you open a lobster clasp?

What is a snap lock clasp?

Snap Lock Clasps are easy to open and close and therefore are an ideal closure for bracelets. The closing mechanism folds over the other half of the clasp to create a secure look. Snap locks look very neat and stylish along with our leather cords, hair-on leather, and suede cords.