How do you make a slip solution for PPF?

For the slip solution, use a combination of water and soap. For the tack solution, use a combination of water and isopropyl alcohol. We recommend mixing two drops of Johnson's Baby Shampoo into a 1000 mL bottle for your slip solution.

How do you mix tack solution?

Recommended proportion for tack solution: 9 parts of water to 1 part of alcohol. If more tack is desired, increase the alcohol concentration to 8 parts of water for 2 parts of alcohol. We do not recommend any higher alcohol concentrations.

How do you get bubbles out of PPF?

Air bubbles will evaporate over several days (or weeks, depending on weather) when the film is exposed to heat. If air bubbles are still on the film, the only way to remove it is to suck the air out with a needle. Expect these things to happen right after a PPF installation.

How long does PPF take to cure?

Give PPF at least seven days to cure before washing the vehicle. If you are using a pressure washer, keep away from the film's edges. It could cause the edges to lift, reducing the protection. If you are planning to wipe the surface, make sure it's hydrated.

Can you use a hair dryer for PPF?

use a heat gun or hair dryer. Warm it up and then push down. use a heat gun or hair dryer. Warm it up and then push down.

Slip Solution and Tack Solution For Paint Protection Film

Can you apply PPF in cold?

Temperature

Temperature is another critical factor in PPF application. If the surface is too hot, paint protection films will adhere too quickly, reducing the time needed to adjust the film. If the surface is too cool, the film will not maintain elasticity and will be hard to properly apply.

Can you use Dawn dish soap to tint window?

o For wetting solution, use a solution of mild dish soap (i.e., Dawn® or Joy®) and water. For a 32oz. spray bottle, add 4 to 5 drops of soap.

Can you overlap PPF?

2. DO NOT apply the PPF to Wrap edges, butt seams, overlaps, complex contoured, ribbed or rough surfaces, or over an overlap. 3. Measure, cut, dry-fit and adjust the PPF before starting the application.

Can I clay bar PPF?

Can I use detailing clay on the film? Yes, detailing clay is similar to the regular paint. You need to wet the surface with a lubricant. Here you can use soapy water as lubricant and then rub the surface with a clay bar.

Can you do Polygel nails without slip solution?

If you don't have slip solution u can use isopropyl alcohol 70% or higher . Super shiny finish. This product is great and very easy to use.

Can you use a heat gun on PPF?

Is it recommended to use heat gun on the GPPF? We recommend steam Gun (steamer) over Heat Gun to avoid damage of PPF due to overheat.

Do you wax before PPF?

So no need to wax prior. The reason for the polish is that you want your paint surface to be as perfect as possible before the PPF is applied. No matter how new the car the installer should do a complete detail or correction before PPF is applied. PPF is a window into what was done to the paint before application.

Can you put PPF over rock chips?

Although PPF is not impervious to all rock chips, it still offers a lot of advantages: PPF is at least 4 times as thick as the clear coat on your paint. In addition to self-healing swirls and scratches, it will also self-heal minor to moderate rock chips as long as the impact does not penetrate the PPF.

Does PPF stop rock chips?

Honestly, among the slew of competitors for paint protection dollars, PPF is the clear-cut favorite, and the only one that truly protects the vehicles paint surface, hood, headlights, rocker panel, or the entire vehicle from road debris, rock chips, and scratches.

Can PPF be DIY?

If you've ever detailed your car before, you might be tempted to try a DIY PPF installation right in your driveway. While this can save you some money up front, a DIY paint protection film installation can actually do more harm than good.

How do you keep a PPF clean?

Standard Ongoing Maintenance for PPF/Clear Bra (15 days +):

If dirty, GENTLY use a wash mitt to clean areas. Keep a regular vehicle wash schedule. E.g. once every 2 weeks for daily drivers. Every 3-4 months apply CarPro Reload to the surface to help with ease of maintenance and water spots.