How do you balance the pH and alkalinity in a pool?

A rule of thumb is 1.5 lbs. of baking soda per 10,000 gallons of water will raise alkalinity by about 10 ppm. If your pool's pH tested below 7.2, add 3-4 pounds of baking soda. If you're new to adding pool chemicals, start by adding only one-half or three-fourths of the recommended amount.

Do you balance pH or alkalinity first?

You should test alkalinity first because it will buffer pH. Your reading should be in the range of 80 to 120 parts per million (ppm). If you need to increase the alkalinity, add an increaser. To lower it, you'll add a sodium bisulfate.

Should I adjust pool pH or alkalinity first?

Important: Because alkalinity protects pH, you must always adjust alkalinity first, then adjust pH, if necessary. Sometimes, getting alkalinity where it needs to be also brings the pH in line. Pro Tip: The recommended alkalinity range in your pool water is 100 ppm to 150 ppm, with 125 ppm being ideal.

How do you balance pH and total alkalinity?

When both Total Alkalinity and pH are too low (TA less than 80 ppm, pH below 6.8), use pH Increaser (sodium carbonate) to bring both levels up. If your Total Alkalinity levels are too high, add pH Reducer (sodium bisulfate).

Does pool shock increase alkalinity?

It's also not uncommon for pool owners to go a bit overboard when shocking their pool, and since chlorine-based pool shock is a high-alkaline substance, it will also naturally raise your pool alkalinity.

Adjusting Ph and Alkalinity in your pool

Why does my pool alkalinity keep dropping?

There is a perfectly natural reason for this: evaporation and agitation of your water leads to a drop in the total alkalinity. If you consider the composition of the total alkalinity in detail, it constitutes the water's carbonate and bicarbonate content.

Does shock change alkalinity?

Another cause for high alkalinity can be when you shock the pool. While this is performed to quickly rid the pool of pollutants, chlorine-based pool shock is highly alkaline, and can raise the water's total alkalinity level in the process.

Does chlorine shock raise pH?

It will slightly raise your pH, so make sure you adjust pH while using it. As the name implies, it will also raise your calcium hardness levels in your pool slightly. It is sold in granular or in pucks/tablets. A close relative of calcium hypochlorite is sodium hypochlorite, commonly known as bleach.

What chemicals should I balance first in my pool?

Total Alkalinity (TA) is the first thing you should balance in your pool water. TA refers to the amount of alkaline material in the water. And since alkaline is a pH stabilizer, the number of alkaline substances in water will affect the pH balance. The ideal Total Alkalinity range for pool water is 80 – 120 ppm.

Is it safe to swim in a pool with low alkalinity?

This means you buy more chlorine and waste more time trying to get to an adequate concentration level with the substance. Asides its effects on your pool, a low alkalinity swimming pool is unsafe for swimmers as the acidic water can cause nasal, eye, and skin irritations.

Does chlorine lower alkalinity?

Most people know that chlorine is an important chemical in keeping pool water safe for swimming. But adding too much chlorine can lower your pool's pH as well as its total alkalinity. When alkalinity falls, it is more difficult to maintain a stable pH.

Does baking soda add pH to pool?

As per standard, 1.25 pounds of baking soda is enough to raise the PH level of a 10,000-gallon pool by 10ppm, so to achieve a 100ppm alkalinity, you would need 12.5 pounds of baking soda for a 100,000 gallon of pool water.

What happens if pH is too low in pool?

Low pH water will cause etching and deterioration of plaster, grout, stone, concrete and tiling. Any vinyl surfaces will also become brittle, which increases risk of cracks and tears. All of these dissolved minerals will hold in the solution of your pool water; which can result in staining and cloudy pool water.

Can I add all pool chemicals at the same time?

You should not add all pool chemicals at the same time. You should also avoid mixing pool chemicals together. Adding chemicals at one time can cause dangerous chemical reactions and serious injuries. In addition, it will make it difficult to balance the pool.

What happens if you put too much shock in a pool?

Although, if you overdo the shock treatment, you risk getting green hair from chlorine due to the excess chlorine oxidizing the copper in the water. You can execute a shock treatment with a few different types of pool shock, just be mindful of how much you're using.

Can I put 2 bags of shock in my pool?

In this case, you should double shock your swimming pool water. To double shock, you will need to add 2 pounds for every 10,000 gallons of water. For instance, if you pool is 20,000 gallons, you will add 4 pounds of shock.

Do I Adjust pH or shock first?

That said, Absolutely pH first. And once it's good, don't bother testing pH again until the shock process is complete and FC has dropped below 10. High chlorine reacts with the reagent and shifts the color, so it won't be accurate.

Will baking soda lower pool alkalinity?

The pH level of baking soda is 8.3, so it takes a lot of it to raise a pool's overall pH level. The upside is that using baking soda will never make a pool's pH level higher than 8.3 (and if the pool's pH level is higher, baking soda will lower it), but it's better at adjusting the overall alkalinity of the water.

Does chlorine raise alkalinity?

There are numerous substances you may add to your pool that raise the total alkalinity of your pool water. The most common substance added to your pool water that raises total alkalinity is cyanuric acid (aka chlorine stabilizer).

How do I adjust alkalinity in my pool?

There are two ways to increase your swimming pools alkalinity level: sodium bicarbonate (baking soda) or any type of alkalinity increaser product. If you choose to purchase an alkalinity increaser product be sure the product is made from sodium bicarbonate, which is the main substance used to raise pH.

Should I add shock or chlorine first?

Low chlorine levels often cause green or hazy water, so if your water looks a little cloudy and you haven't shocked in a while, adding shock is the first step. It is always best to shock the pool in the evening, when the sun if off the water.

Do I add chlorine or stabilizer first?

Open your pool under normal procedures, and let the filter run with its normal amount of chemicals. When all the other chemicals, such as chlorine. pH and alkalinity, are balanced, add the chlorine stabilizer. Add the stabilizer only after the filter has been backwashed to ensure it is cycled through a clean filter.

What is the best time to run your pool pump?

The best time to run your pool pump is during the warmest hour of the day; however, keep in mind that this means you will have higher energy consumption, which may lead to an increase in your electric bill. If you want to save on your energy costs, you can run your pool pump at night to avoid peak hours.