How do I reset my electric mobility scooter?

Push the main circuit breaker button to reset the motor. On some scooters, this is labeled the RESET button.

Is there a reset button on a mobility scooter?

Reset Button

When the scooter is running on a low battery, the main circuit breaker may trip to prevent damage to the motor and electronics. Naturally, all the electrical systems go offline when the breaker trips. This will cause the reset button to pop out at the rear section of your scooter.

Where is my reset button on my electric scooter?

Possible cause : Circuit breaker has been tripped.

The reset button (on the left side of the battery box) will automatically trip and turn off the power if the motor is overloaded. An excessive overload, steep incline or too heavy of a rider could have caused the motor to overheat and tripped the breaker.

Why does my mobility scooter not work?

Batteries. The most common cause of mobility scooter breakdowns is the battery. With constant charging and discharging, scooter batteries lose their ability to hold charge.

Where is the reset button on a power wheelchair?

First, locate the circuit breaker. You can locate it on the battery pack of the chair. The 'reset' button is in the battery pack area. You can press the button if the Jazzy power chair needs to be reset.

Scooter Tip: Why Won't My Scooter Move? Watch to Find Out the Most Common Reason Why

Why is my electric wheelchair not working?

Power Wheelchair Won't Start

Is the power turned on? Check the joystick controller. If the chair has been fully charged, make sure the charger and power cord are not plugged into the unit. Make certain the brake release levers are in drive mode.

Why is my electric wheelchair beeping?

This occurs when the joystick controller detects a problem in the Powerchair. A number of lights on the joystick controller will also flash in conjunction with the beeping sound. Each number of light bars that flash (1 through 10) represents a different fault code which helps locate where the problem has occurred.

Do mobility scooters have fuses?

There is a fuse box containing a fuse on the battery cable for each battery. Check the fuses and replace if necessary. Check all cables and wiring for loose or disconnected cable connectors and frayed or damaged wires.

Why does my mobility scooter keep beeping and won't move?

Beep Codes. Condition: The battery voltage is to low and can not power up the scooter. Solution: Replace charge the scooter completely, or replace the batteries. Condition: The battery voltage is to high and the scooter can not operate.

Why is the green light flashing on my mobility scooter?

If the charging indicator is green, this means the battery is fully charged. In this case, the battery charger must be disconnected from the battery so as not to cause overcharging. If the charging indicator is flashing alternate red/green, this indicates there is an electrical problem with the battery pack.

Where is the circuit breaker on an electric scooter?

Circuit breakers are usually on the outside of the scooter. Fuses are usually located on the outside of the scooter or under the footplate in the wiring harness near the battery pack. If the scooter has a circuit breaker press the reset button to see if it will reset.

What does E4 mean on electric scooter?

E4 -Brake lever

This error code indicates that something is wrong with the brake. This error code can also occur if you start the scooter and hold the brake at the same time. If this is not the case, the brake sensor is defective and the brake lever must be replaced.

What does e3 mean on electric scooter?

This means “Abnormal hall signal from motor”. In the vast majority of cases, it is the motor cable that needs to be re-connected.

Why is my electric scooter not starting?

When your electric scooter doesn't respond, check if the main ignition fuses are turned on. If it's not, switch it on, and start the engine again. If it doesn't start, you need to replace it with a new fuse. It's best to have a technician remove and replace your broken fuse for your safety.

How do I reset my Shoprider scooter?

Locate the circuit breaker on the detachable battery pack under the scooter seat, and press the "Reset" button on the circuit breaker, next to the yellow triangle.

Where is the fuse on a Go Go scooter?

Check the tiller console fuse located under the battery pack. To check a fuse: 1. Remove the fuse by pulling it out of its slot.

Why is my Shoprider mobility scooter beeping?

This occurs when the joystick controller detects a problem in the Powerchair. A number of lights on the joystick controller will also flash in conjunction with the beeping sound. Each number of light bars that flash (1 through 10) represents a different fault code which helps locate where the problem has occurred.

What does 5 beeps mean on a Gogo scooter?

If your Pride Mobility Go-Go Scooter Scooter beeps 5 times, the solenoid brake trip has occurred. The freewheel lever may be in the freewheel position.

Why is my Shoprider beeping?

Very Rapid beep- Batteries are low. Charge & test batteries.

What is the use of fuse in scooter?

What is a Fuse? Your e-scooter fuse is what breaks the circuit when there is an electrical fault that causes too much current to flow. Ideally, the fuse is designed to protect the electric scooter wiring and the scooter if something goes wrong. The e-scooter fuse has a wire piece that easily melts.

How do you fix a scooter battery that won't charge?

Check the Battery's Condition

Check if the wires are connected tightly. If you smell a burnt plastic smell, the battery or wire might have burned. If you see a burned wire or part of the battery, take it out and replace it with a new one immediately. Additionally, check if there is a battery leak.

How do I unlock my electric wheelchair?

Unlocking Your Electric Wheelchair

The first step, as always, is turning it on. Then you will need to move your joystick forward until you hear the beep. Then backwards again until you hear another beep. There, that's it, now your wheelchair is unlocked and ready to roll!

Why won't my power chair won't charge?

If the battery doesn't charge then it could be the fuse near the charging port that is blown, therefore the batteries aren't receiving the charge. Last but not least, your charger could be bad, to check that you would need a multi meter to measuer the DC voltage with the charger on (you should get about 26 – 29 volts).