How do I know what size pool pump I need?

Divide the pool volume by the number of hours that you would want the pump to be running, so that would be 65,947.5 divided by 6. This would give you 10,991 which means your pump should be able to turn around this much water in 6 hours.

Can a pump be too big for a pool?

Usually, the mindset of pool owners is that a bigger pump is better. A bigger pump is not better. A pool pump can actually be too big for a pool.

What size pool pump do I need for a 15000 gallon pool?

10,000 – 15,000 gallon pools need a pool pump with flow rate between 20 and 35 GPM. Based on our flow rate per pump size(in hp) table above, a 1hp pool pump will generate this flow rate.

Can I replace my 1 HP pool pump with a 1.5 HP?

So to answer the question, yes, you can replace your 1hp pool pump with a 1.5hp pool pump, but only if your situation calls for it. If you've determined that your current pump is too small for your pool, then we'll suggest replacing it with a larger ECO pump like the Water TechniX Pump Alpha ECO.

How do I choose a new pool pump?

How To: Size A Pool Pump

What is the difference between 1 HP and 1.5 HP pool pump?

As I mentioned before, the 1.5 HP PowerFlo LX has only 1 GPM more flow rate than the 1 HP PowerFlo LX so very little difference between the two pumps. However, for an 18" filter, you don't want to exceed more than about 35 GPM.

How big of a pump do I need for my above ground pool?

What Size Pool Pump is right for my Above Ground Pool? Round Above Ground Pool: For pools up to 24 Ft Round, use a 1 HP pool pump. For pools over 24 Ft Round, we recommend using a 1.5 HP pool pump.

Is a 2 speed pool pump worth it?

At River Pools, we used two speed pumps for years with great success. They are quite a bit more expensive to purchase than single speed pumps and last the same amount of time, which is typically 3-8 years. On average, a two-speed pump will save about 50%-70% on energy cost compared to a one-speed pump.

How many gallons per minute does a 2.0 HP pool pump?

The maximum flow into the pump will be 73 gallons per minute for each intake line. The maximum flow into the pump is 42 gallons per minute for each 1.5 inch intake line.

How many gallons per minute does a 1 hp pump?

The typical efficiency of most hydraulic equipment runs at about 60 percent to 75 percent. One horsepower equals 3,960 gallons/minute/feet.

What HP pump do I need?

Horsepower theoretically required for pumping water equals the gallons per minute multiplied by the head in feet, and divided by 4.000 For power recommended, divide by 2000 instead of 4000.

What size pool pump do I need for a 30 000-gallon pool?

Pool gallonage x 2 (the recommended number of cycles in a day) ÷ daily hourly run time ÷ 60 (minutes in an hour). So, for a 30,000-gallon pool that runs continuously (24-hours), the formula is: 30,000 x 2 ÷ 24 ÷ 60 = 41.6 or rounded up it's a 42 GPM minimum flow rate.

What happens if I oversize my pool pump?

A pool pump that is larger than needed has a more powerful motor and circulates water at a higher flow rate. This uses significantly more energy to pump the same amount of water and puts additional stress on your pipes and filter, meaning you'll need to replace them sooner.

Do you run pool pump while swimming?

Chemicals that you add to your pool while the water is circulating don't need to be recirculated; they will stay mixed even if you don't pump the water continually. Although it's generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time.

What size filter do I need for a 10000 gallon pool?

With pool filters, it's best to err on the larger size so it can handle the power of your pump. A helpful rule of thumb is to choose a filter with at least 1 square foot per 10,000 gallons pool capacity.

What is the best speed to run a pool pump?

If you are running your pool pump to filter and turn your water over, we recommend using the middle and lower speed settings. For example, for the first few days, you might run the pump at 2500 RPMs to see what your pool looks like. Next, you might dial it down to 1600 RPMs.

How long do pool pumps last?

On average, pool pumps last eight to 12 years before needing replacement. Over time, it's normal for pool parts to begin to wear down. In addition, swimming pool technology has come a long way in the last decade.

Which is better Pentair vs Hayward?

The Hayward EcoStar has better energy efficiency and the Pentair IntelliFlo has a reputation for longevity with a proven track record. It's a close battle between the two pumps and it really comes down to personal preference.

What size pump do I need for a 27 foot pool?

For round above ground pools up to 24 ft. ( pools with less than 15,300 gallons) use a 1 HP pump. For round above ground pools over 24 ft. (pools with more than 15.300 gallons) use a 1.5 HP pump.

What size pool pump do I need for a 25000 gallon pool?

Your 25,000-gallon pool needs an output of 52 gallons per minute to circulate the water once every eight hours.

How do I calculate pool pump flow rate?

Divide the total gallons of water in the pool by the turnover rate in hours. Ideal turnover rate is between six and eight hours. To run the pump less time each day, lower the turnover rate. This will give you the gallons per hour or GPH.

Does HP matter for pool pump?

For instance, a pool with water features (deck jets, waterfall, etc) tied into the main pool pump might require a higher horsepower to provide enough flow. The same would hold true for installations with a spa or solar panels running off of the pool pump. Long runs of pipe might also require more power.

Can I replace my own pool pump?

A professional electrician will be needed to disconnect the wiring before a pump can be removed. Once a new pump is installed, an electrician will again be necessary to reconnect the wires to the new pump. A do-it-yourself homeowner with basic mechanical aptitude can replace the pool pump in a relatively short time.

How high can a 0.5 HP pump lift water?

Pump: Their pumps are 10 stage pumps with their 0.5HP water pump capacity of water-lifting is up to 215 feet. Suitability: They are suitable for a minimum of 4-inch borewells to 300 feet deep ones.