How do I fix the orange flame on my water heater?

Why is my hot water heater flame orange?

Orange – Orange flame is usually dust or dirt being burnt. Yellow – Air is not getting to the flame, this needs to be inspected immediately. An adequate supply of combustion and ventilating air must be available without obstructions.

Why is my water heater flame yellow?

A yellow flame occurs when there is not enough air coming to the flame. An orange or red flame happens when the dust and other debris burn together with the gas.

How do you fix a yellow flame on a gas heater?

Gas burners burn blue if the ratio of fuel to air is correct. A yellow burner flame is a symptom that the burner is not getting enough air for complete combustion of the gas. Correcting this problem involves adjusting the burner's air shutter to admit more air, something that an experienced do-it-yourselfer can do.

Why are my gas flames orange?

A gas flame appearing yellow or orange in color or behaving with pops of yellow or orange indicates an improper ratio of oxygen for combustion. Often this improper combustion is temporary and could be caused by dust particles or a dirty burner that needs cleaning.

Rheem Water Heater - Yellow Flames

What color should the flame be in a hot water heater?

1 Answer. The flame of any natural-gas appliance should be blue in color (with maybe a little yellow at the very tip of the flame). The orange flame of your water heater indicates that the gas is not combusting efficiently, and it's a sure sign that your heater needs adjustment or repair.

What is the best setting for a gas water heater?

Know the Ideal Setting: The best setting for gas water heaters is around 115 to 120 degrees Fahrenheit. Oftentimes, water heaters will have additional options to either lower or increase the temperature of the water inside.

What color should a pilot light flame be?

Inspecting a Gas Furnace Pilot Light Flame

A natural gas flame should be a bright blue color with a small amount of yellow at the very tip. A propane flame will have more of a bluish-green flame with a tinge of yellow at the tip. The flame should strong enough to cover about 1/2 inch at the end of the thermocouple tip.

What should hot water heater flame look like?

The correct flame color should be a light blue with the minimum of yellow tips. Incorrect flame color is yellow or sharp blue orange. If you see the burner flame color is yellow and lazy do the following: Provide sufficient fresh air to the water heater, especially if the unit is installed in the confined area.

Why is my hot water yellow and cold water clear?

Reasons for yellow bathwater: The plumbing in your home is rusty. If your water is discolored each morning, or after you haven't used the faucets for a while, but then it begins to run clear after a few minutes, you likely need to replace rusted pipes in your home. The faucet to the shower or bath is rusty.

How long do water heaters last?

It would be nice to know when the time is right to replace your water before it springs a leak and causes an inconvenience or worse yet, damage to your home. Typically a residential hot water heater lasts between 6 and 13 years. Beyond 12 years, you are on borrowed time!

Why is my gas flame orange and not blue?

If you see orange, yellow or red flames instead of blue flames, the burners may need cleaning or adjusting. The orange colour warns you that the gas stove has inappropriate combustion, and it may emit treacherous levels of carbon monoxide gas (CO).

What is the difference between a yellow gas flame and an orange gas flame?

There is a yellow flame. Carbon monoxide is produced. The burning of dust is represented by the orange flame.

Does orange flame mean carbon monoxide?

If you see orange flames instead of blue flames, the burners may need cleaning or adjusting. The orange color alerts you to your gas stove's improper combustion, which may emit unsafe levels of carbon monoxide gas.

What color should the flame be on a gas heater?

The burner flames from your natural gas furnace should look blue or almost completely blue. A healthy natural gas furnace flame is characterized by a roaring blue flame with a light blue triangle in its center. There may be a tiny tip of yellow.

What does a yellow flame indicate?

A red or yellow flame is a flame being starved of oxygen, creating incomplete combustion. The flame will be at a much lower temperature and will seem more sooty. The yellow colour comes from the soot particles produced by the flame.

How often does a flame sensor need to be cleaned?

The service life of a furnace is 10 to 20 years on average. This means you'll have to replace a flame sensor once, twice or three times over the course of the furnace's life. Having a bad flame sensor is completely normal–you just need to know how to properly identify when it's gone bad so you can replace it on time.

How do I know if my flame sensor is dirty?

How much does it cost to replace a flame sensor?

Flame Sensor

It stops your furnace from letting off large amounts of natural gas if it's not working properly. If the sensor is bad, it won't be able to sense heat and will turn the furnace off. The average cost to repair or replace a flame sensor is between $75–$200.