How deep should fence posts be buried?

The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet). Add about 6 inches of QUIKRETE All-Purpose Gravel into the bottom of the hole. Then compact and level the gravel using a post or 2x4.

How deep should an 8 foot post be in the ground?

For an average fence post, about 6 to 8 feet tall, prepare to dig a post hole about 2 feet deep. To install a fence post, you'll need a shovel or post digger, a 6-foot level, soil, and gravel or crushed stone.

How deep should I bury a 10 foot post?

The general rule of thumb when setting a post is that the depth of the post's hole needs to be one-third to one-half of the actual above-ground height of the post. So, a six-foot-high finished post ideally needs to be buried three feet into the ground.

Do fence post need to be below the frost line?

For example, a 6-foot tall fence will need at least 2 feet of post in the ground. Consider the frost line in your area. The bottom of the post needs to sit below the frost line (consult local codes for exact requirements). The frost line (also called frost depth) varies from region to region.

How many bags of cement do I need for a fence post?

1 – 4 bags of concrete per fence post are typically what's needed. This depends on the type of soil, fence design, height, post size and bag weight. In general the depth of the post's hole needs to be 1/3 to 1/2 of the above ground height of the post.

How To Build A Fence: How Deep Should Fence Posts Be Set?

How do you keep fence posts from rotting in concrete?

Fill the first three inches up with gravel so the end of the post doesn't come into contact with the dirt. Gravel allows water to drain quickly away from the post and into the soil. Be sure to place the post in the center of the hole. Finally, fill the entire hole up with cement to the top.

Is quikrete good for fence posts?

The best concrete mix for fence posts I've found is Quikrete Fast Setting Concrete Mix in a 50 lb bag. It's 4000 psi, easy to work with, sets up fast, and doesn't need to be mixed. Just pour it in the hole and soak with water.

How long does it take for a fence post to set in concrete?

Typically, you can apply some weight to the posts after 4 hours, but it's a good idea to wait at least 24 hours before resuming fence construction. Standard concrete mixes may take up to two hours to set and should cure for 24 to 48 hours before any forces are applied to the posts.

Should you mix concrete for fence posts?

Fast-setting concrete is ideal for setting posts because there's no mixing—you simply pour the dry concrete from the bag right into the hole, then add water.

How deep should a 6ft fence post be?

The width of the post hole should be 3 times the width of diameter of the post. For example, if you are erecting a 6 foot high fence using 4 inch fence posts, the posts need to be 6 feet above the ground. 6 divided by 3 is 2, therefore the depth of the hole required is 2 feet.

What size post should I use for a 6 foot fence?

Post lengths for fences start at 8 or 10 feet for a 6-foot-tall fence. They are commonly four-by-fours, which measure approximately 3 1/2 by 3 1/2 inches, or six-by-sixes, at around 5 1/2 by 5 1/2 inches.

What size post do you use for an 8 foot fence?

A common rule of thumb, is to dig the hole 3 times as large as the post, and to a depth of 1/3-1/2 of the post height above ground. so for a 8' high fence, using 4x4 posts. dig the holes 12" in diameter, to a depth of 2 1/2 - 4'. Of course, that's assuming you're setting the posts in concrete.

How much concrete do I need for a post hole?

Most fence post holes will need between 1 - 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post. Depth of the hole is one-third to half the above ground height of the fence post.

How do you dig holes for a fence post?

How many bags of Postcrete do you need per post?

The exact amount of Post Mix Concrete needed will vary depending on the width and depth of the hole, but as a general rule you'll need about one and a third bags for a standard fence post. A gate post, which works harder than a fence post due to the movement of the gate, may require three or four bags.

Can you pour concrete in the rain for fence posts?

Calcium chloride is an accelerating agent which when added to concrete will increase the rate of early strength or shorten the time of setting of the mixture. Calcium chloride is the most common accelerator used when speaking about concrete. Avoid setting your fence posts in the rain!

What happens if you add too much water to quikrete?

NOTE: the more water that is added to the mix the weaker it becomes; adding one extra quart of water per 80 lb bag can reduce the strength of the concrete by up to 40%.

Is rapid set concrete as strong as normal concrete?

Fast-setting concrete isn't just simple and fast, it's also durable and strong, reaching 4000 psi — or pounds of force per square inch —after a month. That's stronger than the concrete used for foundations on most homes.

How long will a treated 4x4 post last in the ground?

A treated 4×4 will last 20 to 25 years in the ground if the conditions in the soil and climate are favorable. That number could increase to 40 to 75 years if you install the treated 4×4 in a cement ring rather than the soil. There are a few factors that influence how long the 4×4 can last in the ground.

How long do pressure treated posts last in concrete?

A PT post will last a long time in concrete, maybe 5 to 10 years in soil alone. I suggest you embed the post in concrete, trowel a peak around the post so water runs off, and don't let the PT post come in contact with the ground.

What do you put between wood and concrete?

Anyplace where wood meets the ground or concrete, the lumber must be pressure treated. For additional moisture protection, a gasket or strip of closed-cell foam can be installed between the concrete foundation and the sill plate.

What concrete is best for fence posts?

Fast-setting concrete is ideal for installing fence posts since it doesn't need to be mixed in a bucket or a wheelbarrow. Once you've finished digging your post holes, add about three to four inches of gravel into the bottom and compact it using a post or a 2x4.

How big of a hole do you need for a 4x4 post?

A general rule of thumb is to dig the diameter of the hole at least 3-4 times the diameter of the post. For example, if setting 4 x 4 wood posts, dig holes 9-12" in diameter. Posts should be centered in the hole and the posts should always have concrete under them.