Can you stain after Thompson's Water Seal?

Thompson's® WaterSeal® Wood Sealers can be applied to damp wood, so you only have to wait about two hours to begin applying stain. Some of our other products require that the wood dry for 48 hours before applying a deck coating.

Can you stain wood after it's been sealed?

If you're wood has already been sealed by polyurethane or another finish, the wood stain won't work, because it can't reach the pores of the wood. Visually inspecting your piece is the easiest way to tell if the wood has already been sealed.

Can you stain a deck that has been sealed?

Remove any old stains or sealers If you have a deck that has been previously stained or sealed, the first step is to strip these from the surface and pores of the wood. Even if there is no visible stain or sealer on the surface, the pores will still be clogged with sealer and prevent the new stain from bonding.

Should you stain or water seal first?

The order which you apply stains and sealants varies on what you're currently working with. For the best performance, we recommend stain first, seal second, and apply Advance Topcoat third. This will provide the best protection of your home.

Can you stain after water seal?

Thompson's® WaterSeal® Wood Sealers can be applied to damp wood, so you only have to wait about two hours to begin applying stain.

Thompson's WaterSeal Total All-in-One Stain + Sealer

Can you paint or stain over Thompson's water seal?

Things You'll Need

Paint can be applied to water sealers, but the drying time of the sealer itself is the most important part of this task. For best results, prime the water-sealed wood first. Use either a latex-based or an oil-based primer as your first coat of paint before applying the finishing coat.

How long does Thompson's Water Seal take to cure?

Allow at least 48 hours to dry; however drying time will vary depending on the substrate, temperature, and humidity. Allow minimum of 30 days drying time before applying oil based paint over Thompsons® WaterSeal® Clear Wood Sealer.

How many coats of Thompson Water Seal do I need?

Apply 2 coats using brush,roller or sprayer. note: Use at full strength.do not dilute. The second coat should be applied when the first coat has soaked in the surface. For best results do not leave the first coat to dry for more than 1 hour before applying the second coat.

How long does Thompson Water Seal last?

Water Seal can only be used on bare and uncoated brick, stone or concrete. How long will Water Seal last? If applied correctly, Water Seal will last up to 4 years.

When should you not stain a deck?

You want to apply the stain when the wood surface and air are in the temperature range of 50° – 90°F. You also want to avoid the direct application of sunlight. Lastly, do not apply a stain if there is a forecast of rain in the following one to two days, or all your hard work could end up being washed away.

Should I seal my deck before staining?

To protect your deck from both moisture and sun damage, you need to first stain it, then follow that with a clear sealant. You can now find modern products that combine stain and sealant to make complete deck protection a one-step application process, after the necessary prep work.

Can I apply a second coat of deck stain a week later?

Don't allow the product to dry out between coats. this is especially true with waterborne products. Most stains will have some type of waxes or paraffins in them, which work to help them repel water.

Do you seal wood before or after staining?

Most stains should be sealed to prevent bleeding. After smoothing the stained wood, apply a sealer coat of thinned shellac, sanding sealer, or other appropriate sealer. Do not use shellac with NGR or water-base stains. If you plan to finish the piece with polyurethane, make sure the sealer is compatible.

What happens if you stain wood too soon?

If you stain pressure-treated wood too soon, the stain will be unable to fully penetrate the wood, and you will not get the protective benefits of the stain. What is the best stain for pressure-treated wood? An oil-based stain is the best for pressure-treated wood.

Can you stain and seal the same day?

Considering that most commonly used stains take between 12 to 24 hours to dry and cure completely, it's good practice to wait a full 24 hours before applying polyurethane sealer to your workpiece after your stain has been applied.

Can you use too much Thompson Water Seal?

Yes: Applying too much Thompson's WaterSeal clear waterproofer will significantly increase the amount of time it takes to dry, and it may not dry properly at all.

Should I use Thompson Water Seal on pressure treated wood?

On new pressure treated lumber, please allow 30 days before applying Thompson's WaterSeal Wood Sealers. Always perform the splash test before sealing wood. If water absorbs within 5 seconds after you've sprinkled it on the surface, the wood is porous and considered ready to be sealed.

Can you use a roller to apply Thompson's Water Seal?

Thompson's water seal protects your deck from both mildew and mold damage. Can you apply a sealant with a roller? Although it is recommended to use a pump-up sprayer, you can also apply this sealant with a roller, a brush, or a paint pad.

Do you need 2 coats of Thompson's Water Seal?

Thompson's WaterSeal products typically need only one application, but you can apply a second coat of stain to darken the wood, if desired. However, you must wait for the first coat to dry (typically about 2 hours) and apply the second coat within 4 hours of applying the first coat.

How long does Thompson Water Seal need to dry before rain?

COVERAGE Thompson's Water Seal will cover approximately 4 m² per litre. Coverage will vary depending on the texture and porosity of the surface to being treated. DRYING TIME Thompson's Water Seal should be dry in 2 hours under normal conditions.

How well does Thompson Water Seal work?

Thompson's WaterSeal has clearly not been a consumer favorite with deck stains or sealers. Mainly as it does not offer any UV protection and it grays in a few months. The Transparent and Semi-Transparent versions are prone to premature peeling and wearing after about 1 year.

Does Thompson Water Seal darken wood?

Thompson's^® WaterSeal^® offers several choices, from a clear waterproofer to a solid deck stain. A clear waterproofer does not change the wood's natural color. A transparent stain adds a hint of color and shows the most wood grain.

How do you remove Thompson Water Seal?

Steps to Remove the Sealant:

To use mineral spirits, wipe the spirits over the area with a cloth. Let it sit for a few minutes, then scrub the area with a scrub brush. To use a concentrated degreaser, follow the instructions on the label of your selected product.