Can you leave the neutral wire unconnected?

Yes, Just cap off the neutral wire aka "grounded conductor". Like the other Chris said, do not connect to the bare ground just leave as is with a wire nut on the end to keep it insulated.

Can I leave neutral wire disconnected?

In an unbalanced 3 phase electrical load, the line currents are different, which causes the neutral current to flow from the star point of the load to the supply star point. If the neutral wire is broken or disconnected, the out of balanced current cannot return to the supply through the star point, but it must return.

What happens if I dont connect the neutral?

The standard electrical system in US home uses AC or alternating current. With a regular 120-volt AC circuit, the neutral wire provides a return path to earth ground. If the neutral wire disconnects, it would stop the flow of the electricity and break the circuit.

Does neutral wire need to be connected?

Except in very rare situations, all neutral wires in a box must be connected. The neutral is how the current flows back to the supply, so if you don't connect a neutral to one fitting it won't work. You could connect three in one connector, then three in another, and have a link between the two.

What do you do with an unused neutral wire?

It's supposed to be marked/taped though to designate this. Alternatively, it could simply be an unused neutral leg that was brought in with the hot leg and should just be capped if not used. Newer building codes require you to run a neutral leg to switch boxes so that things can be "run" from the box.

Understanding an Open or Loaded Neutral

Can the neutral wire shock you?

If you touch the neutral wire in a live circuit, whether it be a lamp, an appliance or something else, it is the same as touching the active wire. It is only "safe" to touch the neutral wire when there is no current flowing, just as it is "safe" to touch the earth wire (when one exists). That is, "safe" is relative.

Can an open neutral cause a fire?

When there's a loose wire connection, the neutral wire becomes abnormally hot and damages appliances in their wake. Most fires related to an electrical fault have an open neutral to blame.

Can an open neutral cause damage?

Open neutral can result in equipment malfunction, damage, overheat and possibly fire. Open neutral issues discussed in this article can happen in single or three phase distribution system though it more commonly experienced in single phase systems. Open neutral occurs much more frequently than most people would think.

Does neutral wire have power?

To summarize: the hot wire carries electricity from the power supply and takes it to the load (lightbulb). Neutral wires take the used electricity from the load and bring it back to the power supply.

What happens if you don't bond the neutral to ground?

If the ground is not bonded to neutral, then the entire ground circuit in the building becomes close to hot until the circuit breaker trips. Ground rods can have several ohms of resistance to ground, which is far too high to keep the ground to safe Voltage in such a situation.

Should a neutral wire be live?

Neutral is not necessarily zero and assuming it is will likely get you electrocuted. The general idea is that live supplies the voltage and neutral is the return wire. In most installations the live is at the required voltage and the neutral line is connected to ground at some point (so zero volts relative to ground).

What happens if neutral wire touches ground?

In Short if neutral wire touches a earth wire,

An earth wire carrying load current is a risk of electric shock because a person touching this earth may present an alternative path for the load current and thus the risk of electric shock.

Can a hot and neutral wire touch?

A short circuit happens when a “hot” wire (black) touches another hot wire or touches a “neutral” wire (white) in one of your outlets. When these two wires touch, a large amount of current flows, creating more heat than the circuit can handle, so it shuts off.

Why would a neutral wire spark?

So why the sparks? Between the two neutrals, it's because there are downline loads being served by that neutral. When you sever a neutral, you cut off current flow, and the downline load "lifts" the neutral wire to 120V.

Is a neutral wire hot?

Here's a rundown of electrical wires: The black wire is the "hot" wire, it carries the electricity from the breaker panel into the switch or light source. The white wire is the "neutral" wire, it takes any unused electricity and current and sends it back to the breaker panel.

Can you connect neutral to ground bar?

The answer is never. Grounds and neutrals should only be connected at the last point of disconnect. This would be at main panels only.

What happens if neutral touches metal?

So, under normal conditions, if the neutral wire touches the appliance metal housing it would not constitute a shock hazard. The problem occurs if there is an open circuit in the grounded circuit conductor between the appliance and service panel.

What is purpose of neutral wire?

Neutral wire carries the circuit back to the original power source. More specifically, neutral wire brings the circuit to a ground or busbar usually connected at the electrical panel. This gives currents circulation through your electrical system, which allows electricity to be fully utilized.

Why do neutral and ground need to be separated?

With ground and neutral bonded, current can travel on both ground and neutral back to the main panel. If the load becomes unbalanced and ground and neutral are bonded, the current will flow through anything bonded to the sub-panel (enclosure, ground wire, piping, etc.) and back to the main panel. Obvious shock hazard!

What is a floating neutral?

iTechworld portable generators are "floating neutral", meaning that the neutral circuit is not connected to the frame or to earth ground. This also means that both legs on the receptacle are hot legs, which is normal for floating neutral generators.

Do you bond the neutral in a subpanel?

The neutral and ground MUST NOT be bonded at a sub-panel. They should only be bonded at the main service panel. If you bond them anywhere other than the main service, the neutral return current now has multiple paths, including though your ground wire.

What is a bonded neutral?

With a bonded neutral generator, the neutral is connected to the frame of the generator. Safety code requires the neutrals to be averted away from the original source (your panel) and connect to the "first means of disconnect" when using the generator.

Why neutrals and grounds are connected in a main panel?

Without the grounding wire, that misdirected electricity could shock you. At the main service panel, the neutral and grounding wires connect together and to a grounding electrode, such as a metal ground rod, which is there to handle unusual pulses of energy, such as a lightning strike.