Can you hammer a nail into Hardie board?

Fiberboard cement siding can be hand-nailed, but because it's so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun.

Can you put a nail in Hardie board?

Hardie board comes with a 30-year manufacturer's warranty, but that means you need the nails to last at least that long too. James Hardie recommends that nails be hot dip galvanized (at a minimum) or stainless steel (as a best practice).

Can you nail into Hardie board siding?

Fasteners must be corrosion resistant, galvanized or stainless steel. James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above. Fasteners shall be installed between 1 in. and 3/4 in.

Do you nail or screw Hardie board?

Fasten HardieBacker sheets with proper nails or screws (as listed in ''Materials Required'' in the backer installation instructions) every 8'' around the perimeter and all supporting studs. Keep fasteners between 3/8'' and 3/4'' from sheet edges and 2'' in from sheet corners.

What kind of nails do you use on Hardie board?

NAIL TYPE:

Fasteners must be corrosion resistant, galvanized or stainless steel. Electro-galvanized nails are acceptable for use with James Hardie Siding Products, but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails.

3 Common Installation Issues with James Hardie Siding

How do you nail Hardie panels?

James Hardie recommends the use of quality, hot-dipped galvanized nails. James Hardie is not responsible for the corrosion resistance of fasteners. Stainless steel fasteners are recommended when installing James Hardie® products near the ocean, large bodies of water, or in very humid climates.

How do you hang things on Hardie board?

Generally speaking, items can be attached to Hardie® siding by using either corrosion resistant nails or screws. The fasteners must be long enough to go through the siding and into wood or metal substrate (e.g. sheathing or studs).

Should Hardie board be caulked?

James Hardie DOES NOT recommend using caulk or “H”-jointers for the butt joints of HardiePlank® siding with ColorPlus® technology. James Hardie also DOES NOT recommend applying caulk to the horizontal overlap between siding planks (see Figure 2).

Can I drill into Hardie board?

It can be cut and drilled just like wood. However, drilling through cement-fiber siding goes better if you use a carbide drill bit, as opposed to a regular steel drill bit. Cement-fiber siding can be drilled while installed on a house or prior to installation.

Does Hardie siding need to be nailed into studs?

Building codes will usually require installing siding over water-resistant barriers and nailed into the studs every 16 or 24 inches.

What size nails do you use for Hardie siding?

James Hardie recommends using stainless steel finish nails when installing HardieTrim products. Use a 2 in. finish nail to fasten trim together. Longer finish nails may bend.

How long does Hardie board last?

Hardie Board siding is a greater financial investment than vinyl siding, but it lasts longer too. So as you consider this aspect of your decision, realize you will enjoy this outstanding siding for up to 50 years.

Can you pressure wash hardiplank?

The manufacturer recommends that you do not pressure wash your Hardie siding. The hard spray of water from the power washer can damage the surface of the siding.

Can you use roofing nails for Hardie siding?

5. Properly Nail off The Siding. You can shoot Hardie siding on with air powered nailers or use hand driven roofing nails to attach siding to the home or structure. The nails can be ringed- shanked or smooth just make sure you are hitting the studs in the wall.

Can you screw into fiber cement siding?

Fiber cement siding can be nailed by hand or with a pneumatic nailer. It can also be attached using corrosion resistant screws. Use hot-dipped galvanized or stainless steel nails. Nails should penetrate through the sheathing and at least 1” into studs.

What kind of screws do you use on Hardie board?

James Hardie recommends 1-1/4'' long galvanized or STAINLESS steel roofing nails or 1-1/4'' long ribbed waferhead screws in compliance with the tile industry. It is 8-18 x 3/8'' HD.

Can you use Command hooks on Hardie board?

Command™ Outdoor Products can also be used on smooth, sealed and finished surfaces including vinyl siding and fences, doors, windows, decks, gutters and trim. The Outdoor Product line is not recommended for use on rough surfaces, such as cement board, brick or rough-sawn wood.

Can you screw into Hardie board siding?

Yes, you can drive screws into the Hardie board if you use suitable screws. Hardie Board requires using specific screws to work effectively. For best results, use ribbed stainless steel screws with wafer-head.

Can I use a framing nailer for Hardie siding?

The answer is, yes. Framing nail guns can be used for siding installation, if the nail being used is long enough to attach the siding firmly to your exterior wood sheathing. While it's recommended to always use a siding nail gun for siding installation, in a pinch, you may be able to use a framing nailer instead.

What is the difference between board and batten and Hardie board?

Is board and batten the same as Hardie Board? No, they're not the same. Board and batten is the style of siding while Hardie Board is the material manufactured by James Hardie. Hardie Board is a type of fiber cement siding, and it can be used for board and batten.