Can I use 70% alcohol to clean bearings?

Well, pure isopropyl alcohol will clean your bearing nice and fine without damaging it, but if you use let's say 70% isopropyl alcohol, your bearing will start to rust. This is because the other 30% is water, which can lead to rusting and slowing down of the bearing.

Can I use alcohol to clean bearings?

Put the bearings in a container WITH A LID and fill it to the brim with isopropyl alcohol. Cap the container and shake for 5 minutes. If your bearings are still coated in nasty, repeat the process. Set the bearings out to dry.

Is isopropyl alcohol good for cleaning bearings?

Remove the bearing shields and throw your bearings in isopropyl alcohol for a few hours. After they soak and get all the dirt out, take your bearings out of the solvent and let them air dry for about 30 minutes. Lastly lubricate your bearings with a tiny drop of skate lube and put the shields back on.

What solvents can I use to clean my bearings?

Solvents we recommend are Acetone, Methyl Ethyl Ketone, Citrus cleaner, and Denatured alcohol. All of these can be found in the paint section of your local hardware store.

Can I use 91 isopropyl alcohol to clean skateboard bearings?

Yup, 91% is good.

How To Clean Your Skateboard Bearings

What household items can I use to clean bearings?

Half-fill a jar or bottle with acetone. You may also use isopropyl alcohol, non-water-based citrus cleaner, or lemon juice. Just make sure that there's no water in whatever solution you're choosing to use because it will cause rust to develop in the bearings.

What solvent should I use to clean skateboard bearings?

Acetone, isopropyl alcohol and mineral spirits are all good options. When using solvents, wear gloves and avoid contact with your skin. Use a dish or wide-mouthed bottle as a container to soak the bearings for several minutes, occasionally swirling the bearings around in the cleaner.

Can I use acetone to clean bearings?

Pour enough acetone into the container to cover the bearings. Place inside and securely fasten the lid. (Follow the instructions with your cleaning kit carefully). You can leave them to soak and give them a good shake to remove all the dirt.

What can I use to lubricate bearings?

While some bearing applications use oil as a lubricant, grease is the lubricant of choice for 80 to 90 percent of bearings.

Can I clean bearings with white vinegar?

Make sure you use WHITE vinegar, not cider or balsamic. (3) Now place bearing into the vinegar. You will begin to see hydrogen bubbles forming on the bearing (5th pic is bearings in vinegar). Remove the bearing every hour and give it a scrub with the toothbrush or cloth to remove loosened rust.

What type of alcohol is denatured?

Denatured alcohol is ethyl alcohol with toxic or bad tasting additives that make it unsuitable for consumption. The chemical formula of ethyl is C₂H₆O and the formula for isopropyl alcohol is C₃H₈O. The most common additive to denatured alcohol is 5 to 10 percent methanol.

Can you clean sealed bearings?

Very gently remove the rubber seals by prising out the seal from the inner lip. You can use a penknife or small screwdriver but do not push it too far into the bearing or you may damage the retainer (cage). Use a degreaser and some paper cloth to make sure you fully clean away all old grease before relubricating.

Can you clean bearings with wd40?

Using some WD-40® Multi-Use Product, spray the entire surface of the wheel and ball bearing, and leave it to work for a few minutes. Next, submerge the parts into a bowl of clean water, and leave them to soak for an additional few minutes. Your wheels and bearings should now be grime free.

Can you use vinegar to clean skateboard bearings?

Compressed air will speed the process. Pour enough white vinegar into a jar so that the bearing can be completely submerged. Make sure you use WHITE vinegar, not cider or balsamic. … White vinegar does not leave a residue when it evaporates, so you will not need to do additional cleaning.

Can you clean bearings with dish soap?

Gently pry up and around the bearing, making sure not to bend it too far out of shape. The shield should remain flat throughout the process, don't pull up in one spot. Once all shields are off, they should be placed in a bowl of warm water and dish soap. Do not place the shields in acetone/solvent.

Can you clean bearings with degreaser?

Cleaning. Next you need to get all the old crap and grease out of your bearing races. The best bet is to use methylated spirit or just soak the bearings in some solvent or alcohol. If you can find a spray-on degreaser, you can blast all the crap out of your bearings to great effect.

Does citrus cleaner leave residue?

The Citrus Fresh process does not leave a soapy residue in your carpet.