Can I use 7/16 OSB for subfloor?

Oriented strand board, or OSB, is a wood structural panel that can also be used for flooring. It is made from shredded strands of wood pressed together with wax and a special adhesive, then hot pressed into a panel with up to 50 layers of strands. OSB can be used for subfloors, although it is not as common as CDX.

What size OSB is used for subfloor?

Wood Products

For decades, 23/32″-thick OSB has been the most commonly used thickness of OSB subflooring.

Can you use regular OSB as subfloor?

Most local codes allow OSB to be used for subflooring. It's always best to check with your local permitting office before using OSB for your subfloor. One advantage that OSB has over plywood is its larger formatting. For plywood, 8-foot and 10-foot long sheets of plywood are standard.

What thickness subfloor is recommended?

Generally, the minimum thickness for plywood is 5/8 inch; for OSB it's 23/32 inch. However, as joist spacing increases, {rblink 2428}the subfloors need to be thicker. For joist spacing of more than 16 inches up to 19.2 inches on center, the minimum thickness for both plywood and OSB is 3/4 inch.

What kind of sheathing do you use for subfloor?

Plywood has been a standard subfloor material since the 1950s and remains the preferred subflooring for many builders. Standard plywood can be used for subfloors, but a better material is 3/4-inch tongue-and-groove plywood subflooring.

Is 7/16 OSB OK for flooring?

Can I use 7/16 for subfloor?

Glue is sprayed between each layer and the sheet is hot pressed. CDX plywood should be a minimum of 7/16 inch thick. The thicknesses are as follows: 7/16-, 15/32- and 1/2-inch-thick panels require joists spaced 16 inches on center; 19/32- and 5/8-inch-thick panels require joists spaced 20 inches on center.

Is it better to use OSB or plywood for subfloor?

OSB has a lower resale value than plywood due to its lower strength. For this reason, few homeowners prefer OSB in their homes. Apart from costs, plywood is superior in all the other areas, such as the strength of the structure. For this reason, it's a superior material for use on the subfloor.

What size plywood do you use for subfloor?

A plywood subfloor generally uses 1/2-inch to 3/4-inch-thick sheets of plywood that have one rough side (which faces down) and one smooth side, which faces up. The sheets are generally 4 x 8 or 4 x 12 feet in size.

Can you use sheathing as subfloor?

Like Sturd-I-Floor, Rated Sheathing may be plywood or OSB. When used as a subfloor, Rated Sheathing typically requires installation of an additional layer of underlayment on top of it before finish flooring can be applied. The underlayment requirements vary depending on the finish flooring.

Is OSB board suitable for flooring?

OSB also brings a lot of structural qualities that make it a suitable choice for flooring. The manufacturing methods for OSB give it a high durability, and can handle lots of weight.

Can I use OSB instead of plywood?

Industry voices from panel manufacturers or their main trade group—APA – The Engineered Wood Association—say that there's no real difference between the two panels: OSB's and plywood's structural characteristics are equivalent, and they can be used interchangeably.

Which side goes down on OSB subfloor?

OSB also has stamping that reads “This Side Down”. This directs the worker on the correct orientation of the board when installing. The side with the stamp is the smoother side. When installed smooth side down, the rough surface will then face up and give the worker traction for safety.

Can 7/16 OSB span 24 inches?

Wall panels 7/16 Category may be used on studs spaced up to 24” o.c.

Can you use OSB for bathroom subfloor?

OSB Subflooring

However, OSB is known for swelling around the edges when exposed to water. For tile flooring, this can cause bending and cracking, which is why it is discouraged as a subfloor material for tiling.

Does subfloor need to be tongue and groove?

For subflooring, you use tongue and groove plywood. The tongue and groove are only along the 8 foot edges. On the four foot edges, your seams will fall on joist tops, so no need for tongue and groove. But to start off, we will need to remove the tongue so the plywood is tight with the exterior ICF walls.

How thick should subfloor be in bathroom?

Make Sure Your Subfloor is Structurally Stable

The installation guide for 1/4 inch HardieBacker recommends having wood subfloors made of 5/8 inch exterior grade plywood or OSB (oriented strand board) that is 23/32 inches thick.

Can cement board be used as subfloor?

No, Hardie cement board is not meant to be structural, and it will not work in place of a subfloor. The board is very strong in compression and very stable so that the tiles applied to it do not crack, but it has very little shear strength.

Do you nail or screw subfloor?

Ideally, nail down your subfloor using corrosion-resistant nails that will securely hold it in place and last a long time. Screws are a great alternative that you can easily remove, but they are not as sturdy. Screws are superior in terms of reducing floor squeaks, but the installation is slower.

Which is stronger OSB or plywood?

Osb is stronger than plywood in shear. Shear values, through its thickness, are about 2 times greater than plywood. This is one of the reasons osb is used for webs of wooden I-joists. However, nail-holding ability controls performance in shear wall applications.

Why is 7/16 OSB so expensive?

Increasing OSB prices are due to demand over supply, increasing construction starts, and several natural disasters. As contractors, architects, and building owners struggle to offset the high OSB prices, an excellent alternative sheathing product to consider is Barricade Thermo-Brace.

What is the best subfloor for a bathroom?

Pressure treated 3/4″ plywood subfloor is the best subfloor material for bathrooms. Pressure treated plywood is water resistant and will withstand the humid, damp bathroom environment much better than untreated plywood or OSB.

Can you use OSB under vinyl flooring?

Yes, provided it meets the specifications required for subfloor preparation. Bear in mind that plywood and OSB substrates tend to get 'roughed up' during construction, and any imperfections in the surface will eventually telegraph through to the surface of the floor.