Are reboot plasma cutters any good?

We concluded that the Reboot Plasma Cutter 50Amps is the best buy for your money. The leads are a bit short, and it isn't designed for industrial use. However, for anyone needing to do some cutting at home, this slices an excellent cut through 1/2″ plate and can sever 3/8″ material when necessary.

Which is best plasma cutting machine?

What is the best single phase plasma cutter?

Are plasma cutters worth it?

Plasma cutters also cut quickly and efficiently. Plasma takes one-fourth of the time of most similar techniques to make a clean break in a piece of workable metal. Fast process times also minimise the risk of metal abrasion, cuts made in error, or distortion.

Who makes CUT50 plasma cutter?

Amico CUT-50, 50 Amp Professional Plasma Cutter, 100~250V Wide Voltage, 3/4 in.

Amazon Reboot Plasma Cutter = Mind Blown

How thick of steel can a 50 amp plasma cutter cut?

Designed for portable repair work and small business project use, CUT-50 Plasma Cutter cuts a thickness of 3/4 in., and the max severance thickness is 1.0 in. Type: DC Air Plasma Cutter. Supply Power: 110-Volt/230-Volt/60Hz/1-Phase. Rated Input Current: AC 110-Volt/35.7 Amp, 230-Volt/27.1 Amp.

Where are Hobart plasma cutters made?

Hobart machines are American-made in Appleton, Wisconsin. The Airforce 27i plasma cutter is also CSA Certified. This machine features an ergonomic torch design and 12-foot leads on both the torch and the ground lead. The Hobart Airforce 27i features a built-in regulator, air filter and water separator.

What's the cheapest plasma cutter you can buy?

Do plasma cutters wear out?

Plasma cutter consumables are a set of components in your plasma cutter that gradually wear over time until they need to be replaced: they have a life cycle.

How thick can a 45 amp plasma cutter cut?

This is the new digitally controlled 20-55 amps Plasma Cutter Machine with advanced inverter technology and high cutting performance. Designed for portable repair work and small business project use, the CUT-45M Air Plasma Cutter cuts a thickness of 2/5 in. with the max severance thickness at 3/4 in.

What plasma cutters are made in the USA?

Both Hypertherm and Miller build highly regarded plasma cutters in the USA—Hypertherm out of New Hampshire, Miller out of Wisconsin. Hypertherm has been in the business over 40 years, Miller for more than 80 years.

What should I look for when buying a plasma cutter?

Can a plasma cutter cut rusty metal?

Plasma can cut any electrically conductive metal including stainless steel, mild steel, aluminum and more, without pre-heating. Plasma is also great at cutting painted, dirty or even rusted metal.

What are the two types of plasma cutters?

Who makes Viper plasma cutter?

Warranty. JASIC Technologies America is pleased to offer a 1 year warranty on all Viper machine's*. JASIC Technologies America offers warranty across the United States with approved repair service centre's in throughout the country.

Do all plasma cutters need air compressor?

First, the arc heats the metal until it's semi-gaseous. Second, the plasma is forced by blasts of air to finish the cut. Therefore, all plasma cutters need an air compressor to generate enough air pressure for the task. If you buy a plasma cutter without a built-in source of air, you'll need a separate air compressor.

How long should a plasma cutter tip last?

Usually, in normal conditions, we can say that the electrode will wear out first during machine cutting. Typical life time of a set of consumable should last about 1 to 3 hours for about 120 A of mechanized cutting, it's in function of the job.

When should I change my plasma cutter tip?

As you use the electrode, the hafnium/tungsten becomes molten and pieces of it start to blow out through the nozzle as you cut. It develops a pit at the front of the electrode. Once that pit depth is over 1⁄32, it's time to change the consumable.

Is a plasma cutter better than a cutting torch?

Plasma does not require the metal to be preheated before cutting, which saves time, and plasma cutters also outperform oxy-fuel torches when cutting stacked metals. Faster speeds can be achieved on thinner metals with plasma, with minimal or no metal distortion.

Will a plasma cutter cut welds?

There's so much more your plasma cutter has to offer than just cutting. Gouging can be an invaluable skill for removing welds, preparing your workpiece, beveling and so much more. What are the Pros and Cons of Plasma Gouging?

How much does the average plasma cutter cost?

Depending on type, size, and features, a CNC plasma cutting machine could range anywhere from $15,000 to $300,000. That's a big range, but the vast majority of CNC plasma machines sold today are well below the $100,000 mark.

Who makes the titanium plasma cutter?

That's precisely what Harbor Freight Tools' latest offering to the world of metal fabrication offers: top-of-the-line performance at a fraction of the cost. Harbor Freight's Titanium Plasma 45 weighs just over 20 pounds, yet packs a big punch.

Are Amico plasma cutters any good?

This is a great plasma cutter that has options only found on $1000.00 machines. It is built well and operation and controls are all on the front panel. The seller was excellent.

Does Vulcan make a plasma cutter?

Vulcan Welding Tools – Welders, Plasma Cutters, Accessories.