Are Amico plasma cutters any good?

This is a great plasma cutter that has options only found on $1000.00 machines. It is built well and operation and controls are all on the front panel.

Which is best plasma cutting machine?

What is the best single phase plasma cutter?

Are plasma cutters worth it?

Plasma cutters also cut quickly and efficiently. Plasma takes one-fourth of the time of most similar techniques to make a clean break in a piece of workable metal. Fast process times also minimise the risk of metal abrasion, cuts made in error, or distortion.

What's the cheapest plasma cutter you can buy?

Amico Cut-50 Plasma Cutter Review

Where are Hobart plasma cutters made?

Hobart machines are American-made in Appleton, Wisconsin. The Airforce 27i plasma cutter is also CSA Certified. This machine features an ergonomic torch design and 12-foot leads on both the torch and the ground lead. The Hobart Airforce 27i features a built-in regulator, air filter and water separator.

Is a plasma cutter better than a cutting torch?

Plasma does not require the metal to be preheated before cutting, which saves time, and plasma cutters also outperform oxy-fuel torches when cutting stacked metals. Faster speeds can be achieved on thinner metals with plasma, with minimal or no metal distortion.

Do plasma cutters wear out?

Plasma cutter consumables are a set of components in your plasma cutter that gradually wear over time until they need to be replaced: they have a life cycle.

What should I look for when buying a plasma cutter?

How thick can a 45 amp plasma cutter cut?

This is the new digitally controlled 20-55 amps Plasma Cutter Machine with advanced inverter technology and high cutting performance. Designed for portable repair work and small business project use, the CUT-45M Air Plasma Cutter cuts a thickness of 2/5 in. with the max severance thickness at 3/4 in.

What plasma cutters are made in the USA?

Both Hypertherm and Miller build highly regarded plasma cutters in the USA—Hypertherm out of New Hampshire, Miller out of Wisconsin. Hypertherm has been in the business over 40 years, Miller for more than 80 years.

Who makes Viper plasma cutter?

Warranty. JASIC Technologies America is pleased to offer a 1 year warranty on all Viper machine's*. JASIC Technologies America offers warranty across the United States with approved repair service centre's in throughout the country.

Who makes the titanium plasma cutter?

That's precisely what Harbor Freight Tools' latest offering to the world of metal fabrication offers: top-of-the-line performance at a fraction of the cost. Harbor Freight's Titanium Plasma 45 weighs just over 20 pounds, yet packs a big punch.

How thick can a 50 amp plasma cutter cut?

Designed for portable repair work and small business project use, CUT-50 Plasma Cutter cuts a thickness of 3/4 in., and the max severance thickness is 1.0 in. Type: DC Air Plasma Cutter. Supply Power: 110-Volt/230-Volt/60Hz/1-Phase. Rated Input Current: AC 110-Volt/35.7 Amp, 230-Volt/27.1 Amp.

What are the two types of plasma cutters?

Can a plasma cutter cut rusty metal?

Plasma can cut any electrically conductive metal including stainless steel, mild steel, aluminum and more, without pre-heating. Plasma is also great at cutting painted, dirty or even rusted metal.

Are all plasma cutters the same?

There are two common types of plasma cutting torches. The most common torches are the high-frequency starting systems that create a spark with a high-voltage transformer, capacitors, and spark-gap assembly. High frequency torches have the advantage of not using any moving parts and therefore remain fairly dependable.

What size air compressor do you need for a plasma cutter?

As a good rule of thumb, select a compressor that has a flow rate capacity of at least 1.5 times the consumption rate of the plasma cutter.

What gas do you use for plasma cutting?

Nitrogen is often used for higher current plasma systems and for cutting materials up to 3 inches thick. It produces excellent quality cuts on most materials. Oxygen is used when the highest quality mechanized cuts are desired on carbon steel up to 1 -1/4 inch thick. The cut face is smooth, and dross is easy to remove.

How long should a plasma cutter tip last?

Usually, in normal conditions, we can say that the electrode will wear out first during machine cutting. Typical life time of a set of consumable should last about 1 to 3 hours for about 120 A of mechanized cutting, it's in function of the job.

When should I change my plasma cutter tip?

As you use the electrode, the hafnium/tungsten becomes molten and pieces of it start to blow out through the nozzle as you cut. It develops a pit at the front of the electrode. Once that pit depth is over 1⁄32, it's time to change the consumable.

What cuts better than a plasma cutter?

On thicker material, oxy-fuel cuts can be much faster than plasma. For example, a 2” thick piece of carbon steel, requiring a 4” long cut would take a 120-A plasma cutter roughly 1 minute to complete the cut, while an oxy-fuel torch could make the same cut in 15-20 seconds.

Is there anything that a plasma cutter cant cut?

Other materials that cannot be cut include glass, concrete, and ceramics. These materials are non-conductive and are used to insulate electrical products. If you are using a plasma cutter, it simply needs to have a conductivity to complete the electrical connection. Otherwise, it just won't cut at all.

Will a plasma cutter warp metal?

Thin metal and a plasma cutter is going to equal warping. Like others have already noted, you can minimize it by fine tuning your speed and amp settings but the only way I have found that really makes a difference is using a water table.