What size OSB should be on exterior wall?

Exterior walls

Minimum thickness of wall sheathing for use on walls; 3/8" plywood or 5/16" OSB. If you use fibre cement siding, go with 1/2" plywood or 7/16" OSB for the exterior walls.

How thick should exterior OSB be?

Minimum: 7/16” thickness. (Exception: 3/8” for gable end walls structural sheathing.)

How thick should exterior wall sheathing be?

For covering existing siding, 1/2-inch and 3/4-inch thicknesses are commonly used. Standard panels are 2 by 8, 4 by 8, and 4 by 9 feet, although some can be purchased in fan-folded panels that run up to 50 feet long.

What is code for exterior wall sheathing?

1304.13 EXTERIOR WALL SHEATHING. (a) Wooden structural sheathing panels shall be installed on all exterior frame walls.

What type of sheathing is used for exterior walls?

Plywood and OSB are largely considered the best wall sheathing choices because of their overall abilities to hold fasteners well, create a strong bond between studs, and provide some thermal advantages. The “big two” aren't the only selections available however. Structural fiberboard is one such option.

Framing : OSB vs. Plywood - Whats the difference in COST AND PERFORMANCE

Can you use OSB for exterior walls?

Install OSB at least 6 inches off the ground to prevent moisture issues from splashing rainwater. OSB is available with a tongue and grove finish; these boards are made to fit together like a puzzle and increase the strength of the exterior finish.

What size plywood do you use for exterior walls?

The International Residential Code specifies 3/8-inch plywood for sheathing walls with a standard stud spacing of 16 inches, if the siding is nailed to the studs through the sheathing.

Should exterior walls be 2x4 or 2x6?

Modern conventional home building normally makes use of 2x4 lumber (top line above, second from left) in constructing exterior walls. But 2x6 framing, which is a little more than 1.5 times wider, is a common upgrade and is required by some local building codes.

How thick should OSB be for garage walls?

Note: IBC & IRC require a minimum thickness of ⅜” for OSB for wall sheathing.

How thick are residential exterior walls?

However, the standard thickness of ICF exterior walls is 12 inches, reducing room sizes and minimizing the home's square footage. To maintain the original square footage of a building plan, you must increase the overall dimensions of the house, which also impacts the design of the roof and foundation.

What is the R value of 7/16 OSB?

7/16” OSB R-Value = 0.51. 1/2″ OSB R-Value = 0.74.

Is 7/16 OSB OK for roofing?

OSB is the most-used sheathing material for new roofs and roof replacements. You can use 7/16-inch thick OSB sheets without support for areas where the snow load is 30 pounds per square foot because it's durable and maintains building integrity much longer than other sizes.

How Far Can 3/4 OSB span?

Span is permitted to be 24 inches on center where ³/₄-inch wood strip flooring is installed at right angles to joist. Span is permitted to be 24 inches on center for floors where 1¹/₂ inches of cellular or lightweight concrete is applied over the panels.

Can 7/16 OSB span 24 inches?

Wall panels 7/16 Category may be used on studs spaced up to 24” o.c.

Is 11mm OSB OK for shed walls?

Use the correct thickness of board for the proposed use

The thickness of OSB that you need varies on where it is used in a building. Typically 3/4"(18mm) for floors and 3/8" (9mm) for walls and 1/2" (11mm) roof. Also make sure that you get your supporting timbers at the correct spacing.

What size are exterior wall studs?

Wood-framed houses have traditionally been built with 2x4 studs spaced 16-inches on-center. Research has shown exterior framed walls can be adequately supported by 2x6 studs spaced 24-inches on-center.

Is 2x6 framing stronger than 2x4?

The total bearing area of three 2x4s is 15 3/4 square inches; two 2x6s have a bearing area of 16 square inches. In bending, however, such as from a wind load, a 2x6 wall is considerably stronger.

Do you nail or screw OSB board?

A hammer and 8d nails are standard for installing OSB, but you can speed up the installation by using a nail gun. The caveat when using a nail gun is to set the depth of the nail so the head just dimples the surface of the OSB.

Will OSB hold up outside?

Conclusion. OSB is highly resistant to moisture and can be water and weatherproofed for exterior use using good quality paint or stain. It has superior strength to other wood panels and a slower rate of moisture absorption. Properly maintained and protected, OSB will last for decades.

Which side of OSB faces out on walls?

Using OSB Safely

When installing in vertical applications such as wall sheathing, you'll want to orient the smooth or stamped side facing out. The smooth side has a better moisture resistance and will ultimately provide better performance against weather.

Is plywood or OSB better for sheathing?

Industry voices from panel manufacturers or their main trade group—APA – The Engineered Wood Association—say that there's no real difference between the two panels: OSB's and plywood's structural characteristics are equivalent, and they can be used interchangeably.

What material is used for exterior walls?

Polyvinyl chloride (PVC), commonly known as vinyl, is probably the most popular material used for exterior wall siding on homes and other residential applications. It's one of the lowest cost options for exterior wall siding and comes in plenty of styles, colors, and patterns.